SUPER MICRO Computer manual Jumper and Connector Descriptions *AOC-LPZCR1, Jumper Description

Page 8

AOC-LPZCR1/AOC-SOZCR1 User's Guide

2.1.2 Jumper and Connector Descriptions (*AOC-LPZCR1)

Jumper		Description
J2		Activity LED Connector	(*See 2.1.3 for details)
J4		Buzzer Connector	(*See 2.1.3 for details)

Connector		Description
J1		Systerm Management Bus (I2C) (*See I2C cable
		connection on the next page.)
J3		SCSI Mode (On: Enable)
J5		Serial ATA Mode (SATA 2) Mode (On: Enable)
J6		Flash Firmware (On: Flashing Firmware)
J7		SAS Mode (On: Enable)

(DS10-12, DS4),(DS5-8)Diagnostic LED Indicators

2-2

Image 8

Contents Super AOC-LPZCR1/AOC-SOZCR1 Users Guide Table of Contents Introduction AOC-SOZCR1 Series the Terminator Socket Dimm ZCR CardKey RAID Features Operating Systems supportedManagement support AOC-LPZCR1 Series -Low Proﬁle Skyhawk ZCR RAID CardAsia-Paciﬁc HeadquartersEurope Chapter Technical Speciﬁcations and Software Installation AOC-LPZCR1 Card Layout and Jumper LocationsDescription Jumper and Connector Descriptions *AOC-LPZCR1Jumper Description Connectors and LED Indicators *AOC-LPZCR1 Activity LED IndicatorBuzzer Connector I2C Cable ConnectionRear view AOC-SOZCR1 AOC-SOZCR1 Card Layout and Jumper LocationsFront view AOC-SOZCR1 Connector and Header Descriptions *AOC-SOZCR1 SMB Connector and Pin Deﬁnitions *AOC-SOZCR1SMB I 2C 2C cable ConnectionIntelligent Interface Management SAF-TE See Note 1 belowESD Safety Guidelines General Safety GuidelinesCreating the Driver Floppy Disk Adding the Driver into an Existing SystemFor the Windows 32-bit Operating System For the Red Hat/SuSE Operating SystemFor the SuSE Operating System Installing the Driver into a New SystemFor the Red Hat Operating System AOC-LPZCR1/AOC-SOZCR1 Users Guide Conﬁguring Jumper Settings Chapter RAID ConﬁgurationTo Use the Adaptec RAID Conﬁguration Utility Using Adaptecs RAID Conﬁguration UtilitySAS, Sata and Scsi settings Using the Array Conﬁguration Utility RAID Conﬁguration Utility Main MenuTo Create Arrays Array Conﬁguration Utility Main MenuPage To Manage Arrays To assign properties to the new arrayTo View the properties of Existing Arrays Deleting Arrays Setting a Bootable Array Adding a Hotspare Disk Drive Deleting a Hotspare Disk Drive Initializing Disk Drives To initialize Disk drivesPage Page To Rescan Disk drives Rebuilding Arrays To Rebuild an arrayTo Secure Erase Drives Page Using Adaptecs SCSISelect Utility Using the Controller Conﬁguration UtilityUsing the Scsi Conﬁguration Utility Page Page To Use the SATASelect Utility Using Adaptecs SATASelect UtilityUsing the Sata Conﬁguration Utility Using Adaptecs Serial Select Utility To Use the SerialSelect UtilityUsing Physical Conﬁguration Utility Using Disk Utilities To Use Disk Utilities *for Scsi onlyPage To Use Disk Utilities *for Sata and SAS only To Format a Disk DriveTo Exit the Adaptec RAID Conﬁguration Utility To Verify Disk MediaChapter Troubleshooting Contacting Supermicros Technical Support