SUPER MICRO Computer AOC-LPZCR1, AOC-SOZCR1 manual Using Physical Conﬁguration Utility

Page 40

AOC-LPZCR1/AOC-SOZCR1 Manual

3.2.4 Using Physical Conﬁguration Utility

1.Power on your computer. When prompted, press the <Ctrl> and <A> keys simultaneously to enter the RAID Conﬁ guration Utility.

From the RAID Conﬁ guration Main Menu, select "SerialSelect Utility" and press <Enter> to access the Physical Conﬁ guration submenu as shown below:

2.Select "Physical Conﬁ guration" and press <Enter> to access SAS/SATA Device Conﬁ guration submenu.

3.Use the arrow keys to select an item. Press <Enter> to see the conﬁ guration settings of the item selected as shown in the screen above.

4.Use the up/down arrow keys to highlight the setting you wish to conﬁ gure and press <Enter>. (*Note: To load default settings, press <F6>.)

5.Press <Esc> to return to the previous menu and to exit the utility.

3-24

Image 40

Contents Super AOC-LPZCR1/AOC-SOZCR1 Users Guide Table of Contents Introduction AOC-SOZCR1 Series the Terminator Socket Dimm ZCR CardKey RAID Features Operating Systems supportedManagement support AOC-LPZCR1 Series -Low Proﬁle Skyhawk ZCR RAID CardEurope HeadquartersAsia-Paciﬁc Chapter Technical Speciﬁcations and Software Installation AOC-LPZCR1 Card Layout and Jumper LocationsJumper Description Jumper and Connector Descriptions *AOC-LPZCR1Description Connectors and LED Indicators *AOC-LPZCR1 Activity LED IndicatorBuzzer Connector I2C Cable ConnectionFront view AOC-SOZCR1 AOC-SOZCR1 Card Layout and Jumper LocationsRear view AOC-SOZCR1 Connector and Header Descriptions *AOC-SOZCR1 SMB Connector and Pin Deﬁnitions *AOC-SOZCR1SMB I 2C 2C cable ConnectionIntelligent Interface Management SAF-TE See Note 1 belowESD Safety Guidelines General Safety GuidelinesCreating the Driver Floppy Disk Adding the Driver into an Existing SystemFor the Windows 32-bit Operating System For the Red Hat/SuSE Operating SystemFor the Red Hat Operating System Installing the Driver into a New SystemFor the SuSE Operating System AOC-LPZCR1/AOC-SOZCR1 Users Guide Conﬁguring Jumper Settings Chapter RAID ConﬁgurationSAS, Sata and Scsi settings Using Adaptecs RAID Conﬁguration UtilityTo Use the Adaptec RAID Conﬁguration Utility Using the Array Conﬁguration Utility RAID Conﬁguration Utility Main MenuTo Create Arrays Array Conﬁguration Utility Main MenuPage To Manage Arrays To assign properties to the new arrayTo View the properties of Existing Arrays Deleting Arrays Setting a Bootable Array Adding a Hotspare Disk Drive Deleting a Hotspare Disk Drive Initializing Disk Drives To initialize Disk drivesPage Page To Rescan Disk drives Rebuilding Arrays To Rebuild an arrayTo Secure Erase Drives Page Using Adaptecs SCSISelect Utility Using the Controller Conﬁguration UtilityUsing the Scsi Conﬁguration Utility Page Page Using the Sata Conﬁguration Utility Using Adaptecs SATASelect UtilityTo Use the SATASelect Utility Using Adaptecs Serial Select Utility To Use the SerialSelect UtilityUsing Physical Conﬁguration Utility Using Disk Utilities To Use Disk Utilities *for Scsi onlyPage To Use Disk Utilities *for Sata and SAS only To Format a Disk DriveTo Exit the Adaptec RAID Conﬁguration Utility To Verify Disk MediaChapter Troubleshooting Contacting Supermicros Technical Support