SUPER MICRO Computer X9SPV-LN4F, X9SPV-F user manual Super I/O

Page 25

Chapter 1: Introduction

1-6 Super I/O

The Super I/O provides two high-speed, 16550 compatible serial communication ports (UARTs). Each UART includes a 16-byte send/receive FIFO, a programmable baud rate generator, complete modem control capability and a processor interrupt system. Both UARTs provide legacy speed with baud rate of up to 115.2 Kbps as well as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which sup- port higher speed modems.

The Super I/O provides functions that comply with ACPI (Advanced Configuration and Power Interface), which includes support of legacy and ACPI power manage- ment through a SMI or SCI function pin. It also features auto power management to reduce power consumption.

1-13

Image 25

Contents X9SPV-F X9SPV-LN4F Page About This Motherboard About This ManualManual Organization Conventions Used in the Manual Headquarters Contacting SupermicroEurope Asia-PacificTable of Contents Vii Advanced Setup Configurations BOOT Feature Technical Support ProceduresIntroduction Turbo Mode Power TechnologyClock Spread Spectrum Serial ATA Port 0~5Remote Access Configuration Meci Metw Appendix a Post Error Beep Codes Overview ChecklistX9SPV-F/LN4F Image X9SPV-FU57 X9SPV-F/LN4F Motherboard LayoutLED3 X9SPV-F/LN4F Quick ReferencePins 1-2 Reset Ports, LEDs, and ConnectorsJumper Descriptions Motherboard Features Dimensions PowerIpmi PC Health Monitoring CPU MonitoringModel/PN 3rd Gen Motherboard Features TableGHz Model/PN3rd generation Intel Core i7/i5/i3 Mobile processor X9SPV Motherboard Series Block DiagramChipset Overview PC Health Monitoring Recovery from AC Power LossOnboard Voltage Monitoring Fan Status Monitor with SoftwarePower Supply Power Configuration SettingsSlow Blinking LED for Suspend-State Indicator Bios Support for USB KeyboardSuper I/O Page Static-Sensitive Devices PrecautionsUnpacking Motherboard Installation Installation Instructions Installing and Removing DIMMs How to Install SO DIMMsSystem Memory Memory SupportTo Remove SO Dimm SocketBack Panel Connectors and I/O Ports Connectors/I/O PortsPort Locations and Definitions Back Panel USB 2.0#8 PS/2 KB/Mouse Port KB/MouseBack Panel USB 2.0#9 Front Panel USB Pin Definitions Universal Serial Bus USBBackpanel COM1 COM2 header Serial Ports COM1/COM2VGA Port/Connector VGA Connector VGALAN3/4 LAN Ports LAN1~LAN4Front Control Panel JF1 Header PinsNIC1/NIC2 LED Indicators Power LEDFront Control Panel Pin Definitions Overheat OH/Fan Fail LED Power Fail LEDNMI Button Power Button Reset ButtonReset Button B PWR Button ATX Power Connector JPW1 Connecting CablesPin PWR RequiredFan1 Fan2 Fan3 Fan4 Fan HeadersTPM Header JTPM1 Chassis Intrusion JL1Chassis Intrusion TPM Header Power SMB I2C Connector JPI2C1 Sata DOM Power JSD1Sata DOM Power SMB I2C Connector System Management Bus JIPMB1Overheat/Fan Fail LED JOH1 Sgpio Headers T-SGPIO1/2Sgpio Headers OH/Fan Fail LED Internal Speaker/Buzzer SP1 Power LED/Speaker JD1Internal Speaker/Buzzer Explanation of Jumpers Jumper SettingsBios Write Protect JWP1 BMC Enable/Disable JPB1BMC Enable/Disable Bios Write-Protect Cmos Clear Cmos Clear JBT1USB Wake-up USB Wake-Up JPUSB1Watch Dog Reset Watch Dog Reset JWD1Rear side o Onboard IndicatorsIpmi Heartbeat LED LED2 Standby Power LED LED1Overheat / Fan Fail LED3 Sata Connections SATA1~SATA6 Serial ATA and HDD ConnectionsSATA0 SATA1Page Before Power On Troubleshooting ProceduresNo Power No VideoMemory Errors Technical Support ProceduresIf You Lose the System’s Setup Configuration Frequently Asked Questions Page Returning Merchandise for Service Page How To Change the Configuration Data Starting Bios Setup UtilityIntroduction How to Start the Setup Utility Main SetupSupermicro X9SPV-F/LN4F System Time/System DateProcessor System MemoryBOOT Feature Advanced Setup ConfigurationsQuiet Boot Bootup Num-LockProcessor and Clock Options Active Processor Cores Hardware Prefetcher Available when supported by the CPULimit Cpuid Maximum Clock Spread SpectrumTurbo Mode CPU PPM Configuration Power TechnologyConfig TDP Lock Long Duration Power LimitAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration Xhci Mode Xhci Pre-Boot DriverHS Port #1~#4 Switchable USB Ports Per-Port Disable ControlIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings Target Link Speed Available when supported by the hardware IDO Request Enable Available when supported by the hardwareIs Disabled Network Stack Compliance SOS Available when supported by the hardwarePCI-E Slot 1 Option ROM Onboard LAN Option ROM SelectSerial Port 1 Settings / Serial Port 2 Settings Super IO Device ConfigurationIpv6 PXE Support AutoConsole Redirection Settings Remote Access ConfigurationResolution Recorder ModeLegacy OS Redirection Resolution Redirection After Bios PostACPI Configuration Console Redirection Settings for EMSHigh Precision Timer Out-of-Band-Mgmt PortIntel Txtlt Configuration Trusted Computing ConfigurationISCSI Configuration Delete Attempts Add an AttemptChange Attempt Order Event Logs Port Configuration InformationLink Speed Wake On LANChange SmBIOS Event Log Settings When SEL Full Ipmi SettingsSystem Event Log Update Ipmi LAN Configuration BMC Network ConfigurationConfiguration Source Log EFI Status CodesBoot Administrator Password Security SettingsUser Password HDD PasswordExit Save Changes and ResetDiscard Changes and Exit Discard ChangesSave As User Defaults Restore DefaultsRestore User Defaults Boot OverrideRecoverable Post Error Beep Codes Appendix a Post Error Beep CodesPage Driver/Tool Installation Display Screen Installing DriversConfiguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page How to Recover the Uefi Bios Image -the Main Bios Block An Overview to the Uefi BiosTo Recover the Boot Sector Using a USB-Attached Device Page Page