SUPER MICRO Computer X9SPV-F, X9SPV-LN4F Overheat OH/Fan Fail LED, Power Fail LED, NMI Button

Page 40

X9SPV Motherboard Series User's Manual

Overheat (OH)/Fan Fail LED

Connect an LED Cable to the OH/Fan Fail connection on pins 7 and 8 of JF1 to provide advanced warnings of chassis overheat or fan failure. Refer to the table on the right for pin definitions.

Power Fail LED

The Power Fail LED connection is lo- cated on pins 5 and 6 of JF1. Refer to the table on the right for pin definitions.

NMI Button

The non-maskable interrupt button header is located on pins 19 and 20 of JF1. Refer to the table on the right for pin definitions.

OH/Fan Fail Indicator

Status

State Definition

	Off	Normal
	On	Overheat
	On	Overheat
	Flash-	Fan Fail
	Flash-	Fan Fail
	ing

Power Fail LED

Pin Definitions (JF1)

Pin# Definition

5Vcc

6Ground

NMI Button

Pin Definitions (JF1)

Pin# Definition

1Signal

2Ground

	A OH/Fan Fail LED
	B Power Fail LED
	C NMI Button
1	2
Power Button	Ground
Reset Button	Ground
X	X	B
Vcc	OH/Fan Fail LED	A
Vcc	NIC2 LED
Vcc	NIC1 LED
Vcc	HDD LED
Vcc	Power LED
X	X
C NMI	Ground
19	20

JF1 Header Pins

2-14

Image 40

Contents X9SPV-F X9SPV-LN4F Page About This Motherboard About This ManualManual Organization Conventions Used in the Manual Contacting Supermicro HeadquartersEurope Asia-PacificTable of Contents Vii Advanced Setup Configurations BOOT Feature Technical Support ProceduresIntroduction Power Technology Turbo ModeClock Spread Spectrum Serial ATA Port 0~5Remote Access Configuration Meci Metw Appendix a Post Error Beep Codes Checklist OverviewX9SPV-F/LN4F Image X9SPV-F/LN4F Motherboard Layout X9SPV-FU57X9SPV-F/LN4F Quick Reference LED3Pins 1-2 Reset Ports, LEDs, and ConnectorsJumper Descriptions Motherboard Features Power DimensionsIpmi PC Health Monitoring CPU MonitoringMotherboard Features Table Model/PN 3rd GenGHz Model/PNX9SPV Motherboard Series Block Diagram 3rd generation Intel Core i7/i5/i3 Mobile processorChipset Overview Recovery from AC Power Loss PC Health MonitoringOnboard Voltage Monitoring Fan Status Monitor with SoftwarePower Configuration Settings Power SupplySlow Blinking LED for Suspend-State Indicator Bios Support for USB KeyboardSuper I/O Page Static-Sensitive Devices PrecautionsUnpacking Motherboard Installation Installation Instructions How to Install SO DIMMs Installing and Removing DIMMsSystem Memory Memory SupportSO Dimm Socket To RemoveBack Panel Connectors and I/O Ports Connectors/I/O PortsPort Locations and Definitions Back Panel USB 2.0#8 PS/2 KB/Mouse Port KB/MouseBack Panel USB 2.0#9 Universal Serial Bus USB Front Panel USB Pin DefinitionsSerial Ports COM1/COM2 Backpanel COM1 COM2 headerVGA Connector VGA VGA Port/ConnectorLAN Ports LAN1~LAN4 LAN3/4JF1 Header Pins Front Control PanelNIC1/NIC2 LED Indicators Power LEDFront Control Panel Pin Definitions Overheat OH/Fan Fail LED Power Fail LEDNMI Button Power Button Reset ButtonReset Button B PWR Button Connecting Cables ATX Power Connector JPW1Pin PWR RequiredFan Headers Fan1 Fan2 Fan3 Fan4TPM Header JTPM1 Chassis Intrusion JL1Chassis Intrusion TPM Header Sata DOM Power JSD1 Power SMB I2C Connector JPI2C1Sata DOM Power SMB I2C Connector System Management Bus JIPMB1Overheat/Fan Fail LED JOH1 Sgpio Headers T-SGPIO1/2Sgpio Headers OH/Fan Fail LED Internal Speaker/Buzzer SP1 Power LED/Speaker JD1Internal Speaker/Buzzer Jumper Settings Explanation of JumpersBios Write Protect JWP1 BMC Enable/Disable JPB1BMC Enable/Disable Bios Write-Protect Cmos Clear JBT1 Cmos ClearUSB Wake-Up JPUSB1 USB Wake-upWatch Dog Reset JWD1 Watch Dog ResetOnboard Indicators Rear side oIpmi Heartbeat LED LED2 Standby Power LED LED1Overheat / Fan Fail LED3 Serial ATA and HDD Connections Sata Connections SATA1~SATA6SATA0 SATA1Page Troubleshooting Procedures Before Power OnNo Power No VideoMemory Errors Technical Support ProceduresIf You Lose the System’s Setup Configuration Frequently Asked Questions Page Returning Merchandise for Service Page How To Change the Configuration Data Starting Bios Setup UtilityIntroduction Main Setup How to Start the Setup UtilitySystem Time/System Date Supermicro X9SPV-F/LN4FProcessor System MemoryAdvanced Setup Configurations BOOT FeatureQuiet Boot Bootup Num-LockProcessor and Clock Options Hardware Prefetcher Available when supported by the CPU Active Processor CoresLimit Cpuid Maximum Clock Spread SpectrumCPU PPM Configuration Power Technology Turbo ModeConfig TDP Lock Long Duration Power LimitAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration Xhci Pre-Boot Driver Xhci ModeHS Port #1~#4 Switchable USB Ports Per-Port Disable ControlIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings IDO Request Enable Available when supported by the hardware Target Link Speed Available when supported by the hardwareCompliance SOS Available when supported by the hardware Is Disabled Network StackPCI-E Slot 1 Option ROM Onboard LAN Option ROM SelectSuper IO Device Configuration Serial Port 1 Settings / Serial Port 2 SettingsIpv6 PXE Support AutoRemote Access Configuration Console Redirection SettingsRecorder Mode ResolutionLegacy OS Redirection Resolution Redirection After Bios PostConsole Redirection Settings for EMS ACPI ConfigurationHigh Precision Timer Out-of-Band-Mgmt PortIntel Txtlt Configuration Trusted Computing ConfigurationISCSI Configuration Delete Attempts Add an AttemptChange Attempt Order Port Configuration Information Event LogsLink Speed Wake On LANChange SmBIOS Event Log Settings When SEL Full Ipmi SettingsSystem Event Log BMC Network Configuration Update Ipmi LAN ConfigurationConfiguration Source Log EFI Status CodesBoot Security Settings Administrator PasswordUser Password HDD PasswordSave Changes and Reset ExitDiscard Changes and Exit Discard ChangesRestore Defaults Save As User DefaultsRestore User Defaults Boot OverrideAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Installing Drivers Driver/Tool Installation Display ScreenConfiguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page How to Recover the Uefi Bios Image -the Main Bios Block An Overview to the Uefi BiosTo Recover the Boot Sector Using a USB-Attached Device Page Page