SUPER MICRO Computer X9SPV-LN4F, X9SPV-F user manual Power Button, Reset Button B PWR Button

Page 41

Chapter 2: Installation

Reset Button

The Reset Button connection is located on pins 3 and 4 of JF1. Attach it to a hardware reset switch on the computer case. Refer to the table on the right for pin definitions.

Reset Button

Pin Definitions (JF1)

Pin# Definition

3	Reset

4Ground

Power Button

The Power Button connection is located on pins 1 and 2 of JF1. Momentarily contacting both pins will power on/off the system. To turn off the power when set to suspend mode, press the button for at least 4 seconds. Refer to the table on the right for pin definitions.

1 2

BPower Button

A Reset Button

X
Vcc
Vcc
Vcc
Vcc
Vcc
X
NMI
19	20

Power Button

Pin Definitions (JF1)

Pin# Definition

1Signal

2Ground

AReset Button B PWR Button

Ground

Ground

X

OH/Fan Fail LED

NIC2 LED

NIC1 LED

HDD LED

Power LED

X

Ground

JF1 Header Pins

2-15

Image 41

Contents X9SPV-F X9SPV-LN4F Page Manual Organization About This ManualAbout This Motherboard Conventions Used in the Manual Headquarters Contacting SupermicroEurope Asia-PacificTable of Contents Vii Introduction Technical Support ProceduresAdvanced Setup Configurations BOOT Feature Turbo Mode Power TechnologyClock Spread Spectrum Serial ATA Port 0~5Remote Access Configuration Meci Metw Appendix a Post Error Beep Codes Overview ChecklistX9SPV-F/LN4F Image X9SPV-FU57 X9SPV-F/LN4F Motherboard LayoutLED3 X9SPV-F/LN4F Quick ReferenceJumper Descriptions Ports, LEDs, and ConnectorsPins 1-2 Reset Motherboard Features Dimensions PowerIpmi PC Health Monitoring CPU MonitoringModel/PN 3rd Gen Motherboard Features TableGHz Model/PN3rd generation Intel Core i7/i5/i3 Mobile processor X9SPV Motherboard Series Block DiagramChipset Overview PC Health Monitoring Recovery from AC Power LossOnboard Voltage Monitoring Fan Status Monitor with SoftwarePower Supply Power Configuration SettingsSlow Blinking LED for Suspend-State Indicator Bios Support for USB KeyboardSuper I/O Page Unpacking PrecautionsStatic-Sensitive Devices Motherboard Installation Installation Instructions Installing and Removing DIMMs How to Install SO DIMMsSystem Memory Memory SupportTo Remove SO Dimm SocketPort Locations and Definitions Connectors/I/O PortsBack Panel Connectors and I/O Ports Back Panel USB 2.0#9 PS/2 KB/Mouse Port KB/MouseBack Panel USB 2.0#8 Front Panel USB Pin Definitions Universal Serial Bus USBBackpanel COM1 COM2 header Serial Ports COM1/COM2VGA Port/Connector VGA Connector VGALAN3/4 LAN Ports LAN1~LAN4Front Control Panel JF1 Header PinsFront Control Panel Pin Definitions Power LEDNIC1/NIC2 LED Indicators NMI Button Power Fail LEDOverheat OH/Fan Fail LED Reset Button B PWR Button Reset ButtonPower Button ATX Power Connector JPW1 Connecting CablesPin PWR RequiredFan1 Fan2 Fan3 Fan4 Fan HeadersChassis Intrusion TPM Header Chassis Intrusion JL1TPM Header JTPM1 Power SMB I2C Connector JPI2C1 Sata DOM Power JSD1Sata DOM Power SMB I2C Connector System Management Bus JIPMB1Sgpio Headers OH/Fan Fail LED Sgpio Headers T-SGPIO1/2Overheat/Fan Fail LED JOH1 Internal Speaker/Buzzer Power LED/Speaker JD1Internal Speaker/Buzzer SP1 Explanation of Jumpers Jumper SettingsBMC Enable/Disable Bios Write-Protect BMC Enable/Disable JPB1Bios Write Protect JWP1 Cmos Clear Cmos Clear JBT1USB Wake-up USB Wake-Up JPUSB1Watch Dog Reset Watch Dog Reset JWD1Rear side o Onboard IndicatorsOverheat / Fan Fail LED3 Standby Power LED LED1Ipmi Heartbeat LED LED2 Sata Connections SATA1~SATA6 Serial ATA and HDD ConnectionsSATA0 SATA1Page Before Power On Troubleshooting ProceduresNo Power No VideoIf You Lose the System’s Setup Configuration Technical Support ProceduresMemory Errors Frequently Asked Questions Page Returning Merchandise for Service Page Introduction Starting Bios Setup UtilityHow To Change the Configuration Data How to Start the Setup Utility Main SetupSupermicro X9SPV-F/LN4F System Time/System DateProcessor System MemoryBOOT Feature Advanced Setup ConfigurationsQuiet Boot Bootup Num-LockProcessor and Clock Options Active Processor Cores Hardware Prefetcher Available when supported by the CPULimit Cpuid Maximum Clock Spread SpectrumTurbo Mode CPU PPM Configuration Power TechnologyConfig TDP Lock Long Duration Power LimitAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration Xhci Mode Xhci Pre-Boot DriverHS Port #1~#4 Switchable USB Ports Per-Port Disable ControlIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings Target Link Speed Available when supported by the hardware IDO Request Enable Available when supported by the hardwareIs Disabled Network Stack Compliance SOS Available when supported by the hardwarePCI-E Slot 1 Option ROM Onboard LAN Option ROM SelectSerial Port 1 Settings / Serial Port 2 Settings Super IO Device ConfigurationIpv6 PXE Support AutoConsole Redirection Settings Remote Access ConfigurationResolution Recorder ModeLegacy OS Redirection Resolution Redirection After Bios PostACPI Configuration Console Redirection Settings for EMSHigh Precision Timer Out-of-Band-Mgmt PortISCSI Configuration Trusted Computing ConfigurationIntel Txtlt Configuration Change Attempt Order Add an AttemptDelete Attempts Event Logs Port Configuration InformationLink Speed Wake On LANChange SmBIOS Event Log Settings System Event Log Ipmi SettingsWhen SEL Full Update Ipmi LAN Configuration BMC Network ConfigurationConfiguration Source Log EFI Status CodesBoot Administrator Password Security SettingsUser Password HDD PasswordExit Save Changes and ResetDiscard Changes and Exit Discard ChangesSave As User Defaults Restore DefaultsRestore User Defaults Boot OverrideRecoverable Post Error Beep Codes Appendix a Post Error Beep CodesPage Driver/Tool Installation Display Screen Installing DriversConfiguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page To Recover the Boot Sector Using a USB-Attached Device An Overview to the Uefi BiosHow to Recover the Uefi Bios Image -the Main Bios Block Page Page