SUPER MICRO Computer X9SPV-LN4F IDO Request Enable Available when supported by the hardware

Page 77

Chapter 4: AMI BIOS

Configuration Request, permitting access to Extended Functions in an ARI device immediately below the port. The options are Disabled and Enabled.

AtomicOp Requester Enable (Available when supported by the hardware)

When set to Enabled, this feature initiates AtomicOp requests only if Bus Mas- ter Enable bit is in the Command Register set. The options are Disabled and Enabled.

AtomicOp Egress Blocking (Available when supported by the hardware)

When set to Enabled, this feature blocks outbound AtomicOp Requests via Egress ports. The options are Disabled and Enabled.

IDO Request Enable (Available when supported by the hardware)

When set to Enabled, this feature permits setting the number of ID-Based Or- dering (IDO) bit (Attribute[2]) requests to be initiated. The options are Disabled and Enabled.

IDO Completion Enable (Available when supported by the hardware)

When set to Enabled, this feature permits setting the number of ID-Based Or- dering (IDO) bit (Attribute[2]) requests to be initiated. The options are Disabled and Enabled.

LTR Mechanism Enable (Available when supported by the hardware)

When set to Enabled, this feature enables the Latency Tolerance Reporting mechanism. The options are Disabled and Enabled.

End-End TLP Prefix Blocking (Available when supported by the hardware)

When set to Enabled, this feature blocks forwarding of TLPs containing End-End TLP prefixes.

Target Link Speed (Available when supported by the hardware)

When set to Force to 2.5 or 5.0 GT/s, this feature sets an upper limit on the link operational speed of downstream ports by restricting the values advertised by the upstream component in its training sequences. When set to Auto, HW initialized data will be used. The options are Auto, Force to 2.5 GT/s, and Force to 5.0 GT/s.

Clock Power management (Available when supported by the hardware)

When set to Enabled, this feature permits the device to use CLKREQ# signal for power management of link clock in accordance to protocol defined in appropriate form factor specification. The options are Disabled and Enabled.

4-15

Image 77

Contents X9SPV-F X9SPV-LN4F Page Manual Organization About This ManualAbout This Motherboard Conventions Used in the Manual Headquarters Contacting SupermicroEurope Asia-PacificTable of Contents Vii Introduction Technical Support ProceduresAdvanced Setup Configurations BOOT Feature Turbo Mode Power TechnologyClock Spread Spectrum Serial ATA Port 0~5Remote Access Configuration Meci Metw Appendix a Post Error Beep Codes Overview ChecklistX9SPV-F/LN4F Image X9SPV-FU57 X9SPV-F/LN4F Motherboard LayoutLED3 X9SPV-F/LN4F Quick ReferenceJumper Descriptions Ports, LEDs, and ConnectorsPins 1-2 Reset Motherboard Features Dimensions PowerIpmi PC Health Monitoring CPU MonitoringModel/PN 3rd Gen Motherboard Features TableGHz Model/PN3rd generation Intel Core i7/i5/i3 Mobile processor X9SPV Motherboard Series Block DiagramChipset Overview PC Health Monitoring Recovery from AC Power LossOnboard Voltage Monitoring Fan Status Monitor with SoftwarePower Supply Power Configuration SettingsSlow Blinking LED for Suspend-State Indicator Bios Support for USB KeyboardSuper I/O Page Unpacking PrecautionsStatic-Sensitive Devices Motherboard Installation Installation Instructions Installing and Removing DIMMs How to Install SO DIMMsSystem Memory Memory SupportTo Remove SO Dimm SocketPort Locations and Definitions Connectors/I/O PortsBack Panel Connectors and I/O Ports Back Panel USB 2.0#9 PS/2 KB/Mouse Port KB/MouseBack Panel USB 2.0#8 Front Panel USB Pin Definitions Universal Serial Bus USBBackpanel COM1 COM2 header Serial Ports COM1/COM2VGA Port/Connector VGA Connector VGALAN3/4 LAN Ports LAN1~LAN4Front Control Panel JF1 Header PinsFront Control Panel Pin Definitions Power LEDNIC1/NIC2 LED Indicators NMI Button Power Fail LEDOverheat OH/Fan Fail LED Reset Button B PWR Button Reset ButtonPower Button ATX Power Connector JPW1 Connecting CablesPin PWR RequiredFan1 Fan2 Fan3 Fan4 Fan HeadersChassis Intrusion TPM Header Chassis Intrusion JL1TPM Header JTPM1 Power SMB I2C Connector JPI2C1 Sata DOM Power JSD1Sata DOM Power SMB I2C Connector System Management Bus JIPMB1Sgpio Headers OH/Fan Fail LED Sgpio Headers T-SGPIO1/2Overheat/Fan Fail LED JOH1 Internal Speaker/Buzzer Power LED/Speaker JD1Internal Speaker/Buzzer SP1 Explanation of Jumpers Jumper SettingsBMC Enable/Disable Bios Write-Protect BMC Enable/Disable JPB1Bios Write Protect JWP1 Cmos Clear Cmos Clear JBT1USB Wake-up USB Wake-Up JPUSB1Watch Dog Reset Watch Dog Reset JWD1Rear side o Onboard IndicatorsOverheat / Fan Fail LED3 Standby Power LED LED1Ipmi Heartbeat LED LED2 Sata Connections SATA1~SATA6 Serial ATA and HDD ConnectionsSATA0 SATA1Page Before Power On Troubleshooting ProceduresNo Power No VideoIf You Lose the System’s Setup Configuration Technical Support ProceduresMemory Errors Frequently Asked Questions Page Returning Merchandise for Service Page Introduction Starting Bios Setup UtilityHow To Change the Configuration Data How to Start the Setup Utility Main SetupSupermicro X9SPV-F/LN4F System Time/System DateProcessor System MemoryBOOT Feature Advanced Setup ConfigurationsQuiet Boot Bootup Num-LockProcessor and Clock Options Active Processor Cores Hardware Prefetcher Available when supported by the CPULimit Cpuid Maximum Clock Spread SpectrumTurbo Mode CPU PPM Configuration Power TechnologyConfig TDP Lock Long Duration Power LimitAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration Xhci Mode Xhci Pre-Boot DriverHS Port #1~#4 Switchable USB Ports Per-Port Disable ControlIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings Target Link Speed Available when supported by the hardware IDO Request Enable Available when supported by the hardwareIs Disabled Network Stack Compliance SOS Available when supported by the hardwarePCI-E Slot 1 Option ROM Onboard LAN Option ROM SelectSerial Port 1 Settings / Serial Port 2 Settings Super IO Device ConfigurationIpv6 PXE Support AutoConsole Redirection Settings Remote Access ConfigurationResolution Recorder ModeLegacy OS Redirection Resolution Redirection After Bios PostACPI Configuration Console Redirection Settings for EMSHigh Precision Timer Out-of-Band-Mgmt PortISCSI Configuration Trusted Computing ConfigurationIntel Txtlt Configuration Change Attempt Order Add an AttemptDelete Attempts Event Logs Port Configuration InformationLink Speed Wake On LANChange SmBIOS Event Log Settings System Event Log Ipmi SettingsWhen SEL Full Update Ipmi LAN Configuration BMC Network ConfigurationConfiguration Source Log EFI Status CodesBoot Administrator Password Security SettingsUser Password HDD PasswordExit Save Changes and ResetDiscard Changes and Exit Discard ChangesSave As User Defaults Restore DefaultsRestore User Defaults Boot OverrideRecoverable Post Error Beep Codes Appendix a Post Error Beep CodesPage Driver/Tool Installation Display Screen Installing DriversConfiguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page To Recover the Boot Sector Using a USB-Attached Device An Overview to the Uefi BiosHow to Recover the Uefi Bios Image -the Main Bios Block Page Page