SUPER MICRO Computer X9SPV-F Ehci Hand-Off, Xhci Pre-Boot Driver, Xhci Mode, Xhci Streams

Page 72

X9SPV-F/LN4F Motherboard User Manual

EHCI Hand-Off

This item is for Operating Systems that do not support Enhanced Host Con- troller Interface (EHCI) hand-off. When enabled, EHCI ownership change will be claimed by the EHCI driver. The settings are Enabled and Disabled.

XHCI Pre-Boot Driver

This feature enables support for the xHCI pre-boot driver. The options are Enabled and Disabled.

XHCI Mode

Use this feature to select the xHCI controller mode of operation. The options are Smart Auto, Auto, Enabled, and Disabled.

HS Port #1~#4 Switchable

This feature allows for HS port switching between xHCI and EHCI. When set to Disabled, the specified port is routed to EHCI. The options are Enabled and Disabled.

Note: If HS port is routed to xHCI, the corresponding SS port is enabled.

XHCI Streams

Use this feature to enable the maximum primary stream array size for xHCI. The options are Enabled and Disabled.

EHCI1, EHCI2

This feature enables the EHCI interface (USB 2.0). At least one EHCI control- ler must always be enabled. The options are Enabled and Disabled.

USB Ports Per-Port Disable Control

If set to Enabled, this feature allows deactivation of selected USB ports. The options are Disabled and Enabled. If set to Enabled, the following will appear:

USB Port #0~#13 Disable

Select which USB ports to disable. The settings are Enabled and

Disabled.

Deep Sx (EUP)

Select Enabled to enable Deep Sleep State support. The settings are Enabled and Disabled.

4-10

Image 72

Contents X9SPV-F X9SPV-LN4F Page About This Manual About This MotherboardManual Organization Conventions Used in the Manual Contacting Supermicro HeadquartersEurope Asia-PacificTable of Contents Vii Technical Support Procedures Advanced Setup Configurations BOOT FeatureIntroduction Power Technology Turbo ModeClock Spread Spectrum Serial ATA Port 0~5Remote Access Configuration Meci Metw Appendix a Post Error Beep Codes Checklist OverviewX9SPV-F/LN4F Image X9SPV-F/LN4F Motherboard Layout X9SPV-FU57X9SPV-F/LN4F Quick Reference LED3Ports, LEDs, and Connectors Pins 1-2 ResetJumper Descriptions Motherboard Features Power DimensionsIpmi PC Health Monitoring CPU MonitoringMotherboard Features Table Model/PN 3rd GenGHz Model/PNX9SPV Motherboard Series Block Diagram 3rd generation Intel Core i7/i5/i3 Mobile processorChipset Overview Recovery from AC Power Loss PC Health MonitoringOnboard Voltage Monitoring Fan Status Monitor with SoftwarePower Configuration Settings Power SupplySlow Blinking LED for Suspend-State Indicator Bios Support for USB KeyboardSuper I/O Page Precautions Static-Sensitive DevicesUnpacking Motherboard Installation Installation Instructions How to Install SO DIMMs Installing and Removing DIMMsSystem Memory Memory SupportSO Dimm Socket To RemoveConnectors/I/O Ports Back Panel Connectors and I/O PortsPort Locations and Definitions PS/2 KB/Mouse Port KB/Mouse Back Panel USB 2.0#8Back Panel USB 2.0#9 Universal Serial Bus USB Front Panel USB Pin DefinitionsSerial Ports COM1/COM2 Backpanel COM1 COM2 headerVGA Connector VGA VGA Port/ConnectorLAN Ports LAN1~LAN4 LAN3/4JF1 Header Pins Front Control PanelPower LED NIC1/NIC2 LED IndicatorsFront Control Panel Pin Definitions Power Fail LED Overheat OH/Fan Fail LEDNMI Button Reset Button Power ButtonReset Button B PWR Button Connecting Cables ATX Power Connector JPW1Pin PWR RequiredFan Headers Fan1 Fan2 Fan3 Fan4Chassis Intrusion JL1 TPM Header JTPM1Chassis Intrusion TPM Header Sata DOM Power JSD1 Power SMB I2C Connector JPI2C1Sata DOM Power SMB I2C Connector System Management Bus JIPMB1Sgpio Headers T-SGPIO1/2 Overheat/Fan Fail LED JOH1Sgpio Headers OH/Fan Fail LED Power LED/Speaker JD1 Internal Speaker/Buzzer SP1Internal Speaker/Buzzer Jumper Settings Explanation of JumpersBMC Enable/Disable JPB1 Bios Write Protect JWP1BMC Enable/Disable Bios Write-Protect Cmos Clear JBT1 Cmos ClearUSB Wake-Up JPUSB1 USB Wake-upWatch Dog Reset JWD1 Watch Dog ResetOnboard Indicators Rear side oStandby Power LED LED1 Ipmi Heartbeat LED LED2Overheat / Fan Fail LED3 Serial ATA and HDD Connections Sata Connections SATA1~SATA6SATA0 SATA1Page Troubleshooting Procedures Before Power OnNo Power No VideoTechnical Support Procedures Memory ErrorsIf You Lose the System’s Setup Configuration Frequently Asked Questions Page Returning Merchandise for Service Page Starting Bios Setup Utility How To Change the Configuration DataIntroduction Main Setup How to Start the Setup UtilitySystem Time/System Date Supermicro X9SPV-F/LN4FProcessor System MemoryAdvanced Setup Configurations BOOT FeatureQuiet Boot Bootup Num-LockProcessor and Clock Options Hardware Prefetcher Available when supported by the CPU Active Processor CoresLimit Cpuid Maximum Clock Spread SpectrumCPU PPM Configuration Power Technology Turbo ModeConfig TDP Lock Long Duration Power LimitAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration Xhci Pre-Boot Driver Xhci ModeHS Port #1~#4 Switchable USB Ports Per-Port Disable ControlIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings IDO Request Enable Available when supported by the hardware Target Link Speed Available when supported by the hardwareCompliance SOS Available when supported by the hardware Is Disabled Network StackPCI-E Slot 1 Option ROM Onboard LAN Option ROM SelectSuper IO Device Configuration Serial Port 1 Settings / Serial Port 2 SettingsIpv6 PXE Support AutoRemote Access Configuration Console Redirection SettingsRecorder Mode ResolutionLegacy OS Redirection Resolution Redirection After Bios PostConsole Redirection Settings for EMS ACPI ConfigurationHigh Precision Timer Out-of-Band-Mgmt PortTrusted Computing Configuration Intel Txtlt ConfigurationISCSI Configuration Add an Attempt Delete AttemptsChange Attempt Order Port Configuration Information Event LogsLink Speed Wake On LANChange SmBIOS Event Log Settings Ipmi Settings When SEL FullSystem Event Log BMC Network Configuration Update Ipmi LAN ConfigurationConfiguration Source Log EFI Status CodesBoot Security Settings Administrator PasswordUser Password HDD PasswordSave Changes and Reset ExitDiscard Changes and Exit Discard ChangesRestore Defaults Save As User DefaultsRestore User Defaults Boot OverrideAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Installing Drivers Driver/Tool Installation Display ScreenConfiguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page An Overview to the Uefi Bios How to Recover the Uefi Bios Image -the Main Bios BlockTo Recover the Boot Sector Using a USB-Attached Device Page Page