SUPER MICRO Computer X9SPV-LN4F, X9SPV-F user manual PCH-IO Configuration

Page 71

Chapter 4: AMI BIOS

PEG0 ASPM

Set this item to control ASPM (Active State Power Management) support for PEG: Device 1 Function 0. The options are Disabled, Auto, ASPM L0s, ASPM L1, and ASPM L0sL1.

Enable PEG

Use this feature to enable the PEG. The options are Disabled, Enabled, and Auto.

De-emphasis Control

This item sets the De-emphasis control on PEG. The options are -6 dB and -3.5 dB.

Initiate Graphic Adapter

Use this feature to select which device will operate as the primary display. The options are Auto, IGFX/PEG, PEG/On Board, and On Board/PEG. Note: select- ing IGFX/PEG will enable the Intel HD 4000 GPU.

PCH-IO Configuration

This submenu allows you to configure PCH Parameters.

USB Configuration

Legacy USB Support

This feature enables support for legacy USB devices. Select Auto to dis- able legacy support if USB devices are not present. Select Disable to have USB devices available only for EFI applications. The options are Enabled, Disabled and Auto.

USB3.0 Support

This feature enables controller support for USB 3.0 (XHCI) in the BIOS. The options are Enabled and Disabled.

XHCI Hand-Off

This item is for Operating Systems that do not support Exstensible Host Controller Interface (xHCI) hand-off. When enabled, xHCI ownership change will be claimed by the xHCI driver. The settings are Enabled and Disabled.

4-9

Image 71

Contents X9SPV-F X9SPV-LN4F Page Manual Organization About This ManualAbout This Motherboard Conventions Used in the Manual Asia-Pacific Contacting SupermicroHeadquarters EuropeTable of Contents Vii Introduction Technical Support ProceduresAdvanced Setup Configurations BOOT Feature Serial ATA Port 0~5 Power TechnologyTurbo Mode Clock Spread SpectrumRemote Access Configuration Meci Metw Appendix a Post Error Beep Codes Overview ChecklistX9SPV-F/LN4F Image X9SPV-FU57 X9SPV-F/LN4F Motherboard LayoutLED3 X9SPV-F/LN4F Quick ReferenceJumper Descriptions Ports, LEDs, and ConnectorsPins 1-2 Reset Motherboard Features PC Health Monitoring CPU Monitoring PowerDimensions IpmiModel/PN Motherboard Features TableModel/PN 3rd Gen GHz3rd generation Intel Core i7/i5/i3 Mobile processor X9SPV Motherboard Series Block DiagramChipset Overview Fan Status Monitor with Software Recovery from AC Power LossPC Health Monitoring Onboard Voltage MonitoringBios Support for USB Keyboard Power Configuration SettingsPower Supply Slow Blinking LED for Suspend-State IndicatorSuper I/O Page Unpacking PrecautionsStatic-Sensitive Devices Motherboard Installation Installation Instructions Memory Support How to Install SO DIMMsInstalling and Removing DIMMs System MemoryTo Remove SO Dimm SocketPort Locations and Definitions Connectors/I/O PortsBack Panel Connectors and I/O Ports Back Panel USB 2.0#9 PS/2 KB/Mouse Port KB/MouseBack Panel USB 2.0#8 Front Panel USB Pin Definitions Universal Serial Bus USBBackpanel COM1 COM2 header Serial Ports COM1/COM2VGA Port/Connector VGA Connector VGALAN3/4 LAN Ports LAN1~LAN4Front Control Panel JF1 Header PinsFront Control Panel Pin Definitions Power LEDNIC1/NIC2 LED Indicators NMI Button Power Fail LEDOverheat OH/Fan Fail LED Reset Button B PWR Button Reset ButtonPower Button Required Connecting CablesATX Power Connector JPW1 Pin PWRFan1 Fan2 Fan3 Fan4 Fan HeadersChassis Intrusion TPM Header Chassis Intrusion JL1TPM Header JTPM1 System Management Bus JIPMB1 Sata DOM Power JSD1Power SMB I2C Connector JPI2C1 Sata DOM Power SMB I2C ConnectorSgpio Headers OH/Fan Fail LED Sgpio Headers T-SGPIO1/2Overheat/Fan Fail LED JOH1 Internal Speaker/Buzzer Power LED/Speaker JD1Internal Speaker/Buzzer SP1 Explanation of Jumpers Jumper SettingsBMC Enable/Disable Bios Write-Protect BMC Enable/Disable JPB1Bios Write Protect JWP1 Cmos Clear Cmos Clear JBT1USB Wake-up USB Wake-Up JPUSB1Watch Dog Reset Watch Dog Reset JWD1Rear side o Onboard IndicatorsOverheat / Fan Fail LED3 Standby Power LED LED1Ipmi Heartbeat LED LED2 SATA1 Serial ATA and HDD ConnectionsSata Connections SATA1~SATA6 SATA0Page No Video Troubleshooting ProceduresBefore Power On No PowerIf You Lose the System’s Setup Configuration Technical Support ProceduresMemory Errors Frequently Asked Questions Page Returning Merchandise for Service Page Introduction Starting Bios Setup UtilityHow To Change the Configuration Data How to Start the Setup Utility Main SetupSystem Memory System Time/System DateSupermicro X9SPV-F/LN4F ProcessorBootup Num-Lock Advanced Setup ConfigurationsBOOT Feature Quiet BootProcessor and Clock Options Clock Spread Spectrum Hardware Prefetcher Available when supported by the CPUActive Processor Cores Limit Cpuid MaximumLong Duration Power Limit CPU PPM Configuration Power TechnologyTurbo Mode Config TDP LockAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration USB Ports Per-Port Disable Control Xhci Pre-Boot DriverXhci Mode HS Port #1~#4 SwitchableIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings Target Link Speed Available when supported by the hardware IDO Request Enable Available when supported by the hardwareOnboard LAN Option ROM Select Compliance SOS Available when supported by the hardwareIs Disabled Network Stack PCI-E Slot 1 Option ROMAuto Super IO Device ConfigurationSerial Port 1 Settings / Serial Port 2 Settings Ipv6 PXE SupportConsole Redirection Settings Remote Access ConfigurationRedirection After Bios Post Recorder ModeResolution Legacy OS Redirection ResolutionOut-of-Band-Mgmt Port Console Redirection Settings for EMSACPI Configuration High Precision TimerISCSI Configuration Trusted Computing ConfigurationIntel Txtlt Configuration Change Attempt Order Add an AttemptDelete Attempts Wake On LAN Port Configuration InformationEvent Logs Link SpeedChange SmBIOS Event Log Settings System Event Log Ipmi SettingsWhen SEL Full Log EFI Status Codes BMC Network ConfigurationUpdate Ipmi LAN Configuration Configuration SourceBoot HDD Password Security SettingsAdministrator Password User PasswordDiscard Changes Save Changes and ResetExit Discard Changes and ExitBoot Override Restore DefaultsSave As User Defaults Restore User DefaultsRecoverable Post Error Beep Codes Appendix a Post Error Beep CodesPage Driver/Tool Installation Display Screen Installing DriversConfiguring Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control Page To Recover the Boot Sector Using a USB-Attached Device An Overview to the Uefi BiosHow to Recover the Uefi Bios Image -the Main Bios Block Page Page