SUPER MICRO Computer 6015TC-10G, 6015TC-T manual Intel 5100 Chipset System Block Diagram

Page 12

SUPERSERVER 6015TC-T/6015TC-10G User's Manual

JLAN1

JLAN2

VGA CONN

PROCESSOR#2

PROCESSOR#1

0-3

1067/1333

0-2

1067/1333

MT/S

MT/S

0-1

SLOTE-PCI

PCI-EXP x16

DIMMs

Intel 5100

MCH

1-3

PCI-EXP x8

1-2

Oplin

1-1

82598

PCI-E x4

DIMMs

PCI-EXP x1

82573V

PCI-EXP x1

ICH9R

82573L

3.0 Gb/S

SATA

ATI	PCI 33MHz			USB 2.0	USB
ATI	PCI 33MHz
ES1000
				LPC
	RJ45	GB LAN	SIO	FWH
			SIO
		GILGAL	W83627GF
		GILGAL

	RJ45
			MS
		COM1		COM2
			KB

Figure 1-1. Intel 5100 Chipset:

System Block Diagram

Note: This is a general block diagram. Please see Chapter 5 for details.

1-4

Image 12

Contents Super Manual Revision 1.0a Release Date November 11 Preface About This ManualManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Interface Bios Chapter Introduction OverviewServerboard Features Processors MemorySerial ATA PCI Expansion SlotsOther Features ATI Graphics ControllerOnboard Controllers/Ports Intel 5100 Chipset System Block Diagram Server Chassis Features 1U Twin System Notes Sata Backplane/DrivesContacting Supermicro HeadquartersEurope Asia-PaciﬁcPage Chapter Server Installation Preparing for SetupChoosing a Setup Location Unpacking the SystemPage Ambient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Installing the Inner RailsIdentifying the Sections of the Rack Rails Installing the Outer Rails Installing the Rack RailsChecking the Serverboard Setup Installing the Server into the RackInstalling the Server into a Telco Rack Accessing the Inside of the SystemInstalling the Server into a Rack Checking the Components and SetupPreparing to Power On Providing PowerChecking the Sata drives Checking the AirﬂowAccessing the Inside of the System Page Reset PowerChapter System Interface Control Panel ButtonsControl Panel LEDs Overheat/Fan FailSata Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Serverboard Setup PrecautionsHandling the Serverboard Serverboard Installation UnpackingCheck Compatibility of Serverboard Ports and I/O Shield Mounting the Serverboard onto the Serverboard TrayConnecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control Panel I/O PortsProcessor and Heatsink Installation Installing the ProcessorCPU installed in socket PnP cap released From load plate Installing the Heatsink Removing the HeatsinkInstalling Memory Installing Memory ModulesMemory Support PCI Card Installation Adding PCI CardsPCI-Express Slot Serverboard Details X7DCT-10G LayoutJumper Description Default Setting Connector DescriptionX7DCT/X7DCT-10G Quick Reference Connector Deﬁnitions ATX Power ConnectorAuxiliary Power Connector Pwon ConnectorPower On LED Overheat LED OHNMI Button Fan HeadersUniversal Serial Bus USB I2C Power Connector Serial PortsSgpio Header LAN1/2 Ethernet PortsJumper Settings VGA Enable/DisableCmos Clear To Clear CmosLAN1/LAN2 Enable/Disable Gb LAN Enable/DisableWatch Dog Enable/Disable Onboard Indicators Gb LAN LED Indicator LED2Onboard Power LED LED3 LAN1/LAN2 LEDsInstalling Additional Drivers 13 Conﬁguring Supero Doctor Advanced Serverboard Setup Page Chapter Advanced Chassis Setup Control Panel Chassis Front ViewDrive Bay Installation/Removal Accessing the Drive BaysSystem Fans System Fan FailureInstalling/Removing Hot-swap Sata Drives Mounting a Drive in a CarrierPower Supply Power Supply FailureReplacing the Power Supply Removing the Power SupplyRemoving the Power Supply System Bios How To Change the Conﬁguration DataStarting the Setup Utility ChapterRunning Setup Main Bios SetupDefault settings are in bold text unless otherwise noted Press the Delete key to enter SetupMain Bios Setup Menu Main Setup Features Bios DateSystem Time System DateSata Port1, Sata Port2, Sata Port3 and Sata Port4 TypeLBA Format Total SectorsLBA Mode Control Transfer ModeUltra DMA Mode Native Mode OperationAdvanced Setup XBoot FeaturesQuietBoot Mode Post ErrorsAcpi Mode XMemory Cache Cache Base 0-512K Cache Base 512K-640KCache Extended Memory Discrete Mtrr AllocationXpci Conﬁguration XPCI-ExpXAdvanced Chipset Control Enable Multi-Media Timer Patrol ScrubbingDemand Scrubbing USB Host ControllerMachine Checking Available when supported by the CPU C1 Enhanced Mode Available if supported by the CPUHardware Prefetcher Available when supported by the CPU Xcpu Cache Control XI/O Device ConﬁgurationXdmi Event Logging XConsole Redirection XHardware Monitor Logic Fan1-Fan3Fan Speed Control Modes Voltage MonitoringIpmi Speciﬁcation Version Firmware VersionSystem Event Logging Clear System Event LoggingXSystem Event Log/System Event Log List Mode Security XRealtime Sensor DataSupervisor Password Is User Password IsSet Supervisor Password Set User PasswordBoot Password on BootBoot Priority Order/Excluded from Boot Orders Load Setup Defaults ExitExit Saving Changes Exit Discarding ChangesSave Changes Appendix a Bios Post Messages System Cmos checksum bad Default conﬁguration used System timer errorReal time clock error Check date and time settingsFail-Safe Timer NMI Failed Allocation Error for deviceEntering Setup Eisa Cmos not writeablePS/2 Mouse Boot Summary Screen Press F1 to resume, F2 to Setup, F3 for previousDevice IRQ conﬂict Nnnn kB Extended RAM PassedPress F2 to enter Setup System Bios shadowedVideo Bios shadowed PS/2 MousePage Appendix B Bios Post Codes Recoverable Post ErrorsTerminal Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Appendix B Bios Post Codes Page Appendix C System Speciﬁcations ServerboardWeight Power SupplySystem Cooling System Input RequirementsAppendix C System Speciﬁcations