SUPER MICRO Computer 6015TC-10G, 6015TC-T manual XMemory Cache

Page 70

SUPERSERVER 6015TC-T/6015TC-10G User's Manual

Power Button Behavior

If set to Instant-Off, the system will power off immediately as soon as the user hits the power button. If set to 4-sec., the system will power off when the user presses the power button for 4 seconds or longer. The options are Instant-Offand 4-sec override.

Resume On Modem Ring

Select On to “wake your system up” when an incoming call is received by your modem. The options are On and Off.

Power Loss Control

This setting allows you to choose how the system will react when power returns after an unexpected loss of power. The options are Stay Off, Power On, and Last State.

Watch Dog

If enabled, this option will automatically reset the system if the system is not active for more than 5 minutes. The options are Enabled and Disabled.

Summary Screen

This setting allows you to Enable or Disable the summary screen which displays the system conﬁguration during bootup.

XMemory Cache

Cache System BIOS Area

This setting allows you to designate a reserve area in the system memory to be used as a System BIOS buffer into which BIOS can write (cache) data. Select Write Protect to enable this function, and this area will be reserved for BIOS ROM ac- cess only. Select Uncached to disable this function and make this area available for other devices.

Cache Video BIOS Area

This setting allows you to designate a reserve area in the system memory to be used as a Video BIOS buffer into which BIOS can write (cache) data. Select Write Protect to enable the function and this area will be reserved for Video BIOS ROM access only. Select Uncached to disable this function and make this area available for other devices.

7-8

Image 70

Contents Super Manual Revision 1.0a Release Date November 11 About This Manual PrefaceManual Organization Advanced Chassis Setup System SafetyAdvanced Serverboard Setup BiosPreface Table of Contents System Interface Bios Chapter Introduction OverviewSerial ATA Serverboard FeaturesProcessors Memory PCI Expansion SlotsATI Graphics Controller Other FeaturesOnboard Controllers/Ports Intel 5100 Chipset System Block Diagram Server Chassis Features 1U Twin System Notes Sata Backplane/DrivesEurope Contacting SupermicroHeadquarters Asia-PaciﬁcPage Choosing a Setup Location Chapter Server InstallationPreparing for Setup Unpacking the SystemPage Ambient Operating Temperature Rack Mounting ConsiderationsInstalling the Inner Rails Installing the System into a RackIdentifying the Sections of the Rack Rails Installing the Outer Rails Installing the Rack RailsInstalling the Server into a Telco Rack Checking the Serverboard SetupInstalling the Server into the Rack Accessing the Inside of the SystemInstalling the Server into a Rack Checking the Components and SetupChecking the Sata drives Preparing to Power OnProviding Power Checking the AirﬂowAccessing the Inside of the System Page Chapter System Interface ResetPower Control Panel ButtonsControl Panel LEDs Overheat/Fan FailSata Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryPrecautions Chapter Advanced Serverboard SetupHandling the Serverboard Check Compatibility of Serverboard Ports and I/O Shield Serverboard InstallationUnpacking Mounting the Serverboard onto the Serverboard TrayConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel I/O PortsProcessor and Heatsink Installation Installing the ProcessorCPU installed in socket PnP cap released From load plate Installing the Heatsink Removing the HeatsinkInstalling Memory Modules Installing MemoryMemory Support Adding PCI Cards PCI Card InstallationPCI-Express Slot Serverboard Details X7DCT-10G LayoutConnector Description Jumper Description Default SettingX7DCT/X7DCT-10G Quick Reference Auxiliary Power Connector Connector DeﬁnitionsATX Power Connector Pwon ConnectorPower On LED Overheat LED OHFan Headers NMI ButtonUniversal Serial Bus USB Sgpio Header I2C Power ConnectorSerial Ports LAN1/2 Ethernet PortsCmos Clear Jumper SettingsVGA Enable/Disable To Clear CmosGb LAN Enable/Disable LAN1/LAN2 Enable/DisableWatch Dog Enable/Disable Onboard Power LED LED3 Onboard IndicatorsGb LAN LED Indicator LED2 LAN1/LAN2 LEDsInstalling Additional Drivers 13 Conﬁguring Supero Doctor Advanced Serverboard Setup Page Chapter Advanced Chassis Setup Control Panel Chassis Front ViewSystem Fans Drive Bay Installation/RemovalAccessing the Drive Bays System Fan FailureInstalling/Removing Hot-swap Sata Drives Mounting a Drive in a CarrierReplacing the Power Supply Power SupplyPower Supply Failure Removing the Power SupplyRemoving the Power Supply Starting the Setup Utility System BiosHow To Change the Conﬁguration Data ChapterDefault settings are in bold text unless otherwise noted Running SetupMain Bios Setup Press the Delete key to enter SetupSystem Time Main Bios Setup Menu Main Setup FeaturesBios Date System DateLBA Format Sata Port1, Sata Port2, Sata Port3 and Sata Port4Type Total SectorsUltra DMA Mode LBA Mode ControlTransfer Mode Native Mode OperationAdvanced Setup XBoot FeaturesPost Errors QuietBoot ModeAcpi Mode XMemory Cache Cache Extended Memory Cache Base 0-512KCache Base 512K-640K Discrete Mtrr AllocationXpci Conﬁguration XPCI-ExpXAdvanced Chipset Control Demand Scrubbing Enable Multi-Media TimerPatrol Scrubbing USB Host ControllerC1 Enhanced Mode Available if supported by the CPU Machine Checking Available when supported by the CPUHardware Prefetcher Available when supported by the CPU Xcpu Cache Control XI/O Device ConﬁgurationXdmi Event Logging XConsole Redirection Fan Speed Control Modes XHardware Monitor LogicFan1-Fan3 Voltage MonitoringSystem Event Logging Ipmi Speciﬁcation VersionFirmware Version Clear System Event LoggingXSystem Event Log/System Event Log List Mode Security XRealtime Sensor DataSet Supervisor Password Supervisor Password IsUser Password Is Set User PasswordPassword on Boot BootBoot Priority Order/Excluded from Boot Orders Exit Saving Changes Load Setup DefaultsExit Exit Discarding ChangesSave Changes Appendix a Bios Post Messages Real time clock error System Cmos checksum bad Default conﬁguration usedSystem timer error Check date and time settingsEntering Setup Fail-Safe Timer NMI FailedAllocation Error for device Eisa Cmos not writeableDevice IRQ conﬂict PS/2 Mouse Boot Summary ScreenPress F1 to resume, F2 to Setup, F3 for previous Nnnn kB Extended RAM PassedVideo Bios shadowed Press F2 to enter SetupSystem Bios shadowed PS/2 MousePage Terminal Post Errors Appendix B Bios Post CodesRecoverable Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Appendix B Bios Post Codes Page Appendix C System Speciﬁcations ServerboardSystem Cooling WeightPower Supply System Input RequirementsAppendix C System Speciﬁcations