SUPER MICRO Computer 6015TC-T, 6015TC-10G manual Installing the Server into a Rack

Page 23

Chapter 2: Server Installation

Figure 2-3. Installing the Server into a Rack

Checking the Components and Setup

1.You may have one or two processors already installed in each of the two serverboards. Each processor needs its own heatsink. See Chapter 5 for instructions on processor and heatsink installation.

2.Your server system may have come with system memory already installed. Make sure all DIMMs are fully seated in their slots. For details on adding system memory, refer to Chapter 5.

3.You can install two add-on cards to the system. See Chapter 5 for details on installing PCI add-on cards.

4.Make sure all power and data cables are properly connected and not blocking the chassis airﬂow. See Chapter 5 for details on cable connections.

2-7

Image 23

Contents Super Manual Revision 1.0a Release Date November 11 Manual Organization PrefaceAbout This Manual Bios System SafetyAdvanced Serverboard Setup Advanced Chassis SetupPreface Table of Contents System Interface Bios Overview Chapter IntroductionPCI Expansion Slots Serverboard FeaturesProcessors Memory Serial ATAOnboard Controllers/Ports Other FeaturesATI Graphics Controller Intel 5100 Chipset System Block Diagram Server Chassis Features Sata Backplane/Drives 1U Twin System NotesAsia-Paciﬁc Contacting SupermicroHeadquarters EuropePage Unpacking the System Chapter Server InstallationPreparing for Setup Choosing a Setup LocationPage Rack Mounting Considerations Ambient Operating TemperatureIdentifying the Sections of the Rack Rails Installing the System into a RackInstalling the Inner Rails Installing the Rack Rails Installing the Outer RailsAccessing the Inside of the System Checking the Serverboard SetupInstalling the Server into the Rack Installing the Server into a Telco RackChecking the Components and Setup Installing the Server into a RackChecking the Airﬂow Preparing to Power OnProviding Power Checking the Sata drivesAccessing the Inside of the System Page Control Panel Buttons ResetPower Chapter System InterfaceOverheat/Fan Fail Control Panel LEDsSata Drive Carrier LEDs Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsHandling the Serverboard Chapter Advanced Serverboard SetupPrecautions Mounting the Serverboard onto the Serverboard Tray Serverboard InstallationUnpacking Check Compatibility of Serverboard Ports and I/O ShieldConnecting Power Cables Connecting CablesConnecting Data Cables I/O Ports Connecting the Control PanelInstalling the Processor Processor and Heatsink InstallationCPU installed in socket PnP cap released From load plate Removing the Heatsink Installing the HeatsinkMemory Support Installing MemoryInstalling Memory Modules PCI-Express Slot PCI Card InstallationAdding PCI Cards X7DCT-10G Layout Serverboard DetailsX7DCT/X7DCT-10G Quick Reference Jumper Description Default SettingConnector Description Pwon Connector Connector DeﬁnitionsATX Power Connector Auxiliary Power ConnectorOverheat LED OH Power On LEDUniversal Serial Bus USB NMI ButtonFan Headers LAN1/2 Ethernet Ports I2C Power ConnectorSerial Ports Sgpio HeaderTo Clear Cmos Jumper SettingsVGA Enable/Disable Cmos ClearWatch Dog Enable/Disable LAN1/LAN2 Enable/DisableGb LAN Enable/Disable LAN1/LAN2 LEDs Onboard IndicatorsGb LAN LED Indicator LED2 Onboard Power LED LED3Installing Additional Drivers 13 Conﬁguring Supero Doctor Advanced Serverboard Setup Page Chapter Advanced Chassis Setup Chassis Front View Control PanelSystem Fan Failure Drive Bay Installation/RemovalAccessing the Drive Bays System FansMounting a Drive in a Carrier Installing/Removing Hot-swap Sata DrivesRemoving the Power Supply Power SupplyPower Supply Failure Replacing the Power SupplyRemoving the Power Supply Chapter System BiosHow To Change the Conﬁguration Data Starting the Setup UtilityPress the Delete key to enter Setup Running SetupMain Bios Setup Default settings are in bold text unless otherwise notedSystem Date Main Bios Setup Menu Main Setup FeaturesBios Date System TimeTotal Sectors Sata Port1, Sata Port2, Sata Port3 and Sata Port4Type LBA FormatNative Mode Operation LBA Mode ControlTransfer Mode Ultra DMA ModeXBoot Features Advanced SetupAcpi Mode QuietBoot ModePost Errors XMemory Cache Discrete Mtrr Allocation Cache Base 0-512KCache Base 512K-640K Cache Extended MemoryXPCI-Exp Xpci ConﬁgurationXAdvanced Chipset Control USB Host Controller Enable Multi-Media TimerPatrol Scrubbing Demand ScrubbingHardware Prefetcher Available when supported by the CPU Machine Checking Available when supported by the CPUC1 Enhanced Mode Available if supported by the CPU XI/O Device Conﬁguration Xcpu Cache ControlXdmi Event Logging XConsole Redirection Voltage Monitoring XHardware Monitor LogicFan1-Fan3 Fan Speed Control ModesClear System Event Logging Ipmi Speciﬁcation VersionFirmware Version System Event LoggingXSystem Event Log/System Event Log List Mode XRealtime Sensor Data SecuritySet User Password Supervisor Password IsUser Password Is Set Supervisor PasswordBoot Priority Order/Excluded from Boot Orders BootPassword on Boot Exit Discarding Changes Load Setup DefaultsExit Exit Saving ChangesSave Changes Appendix a Bios Post Messages Check date and time settings System Cmos checksum bad Default conﬁguration usedSystem timer error Real time clock errorEisa Cmos not writeable Fail-Safe Timer NMI FailedAllocation Error for device Entering SetupNnnn kB Extended RAM Passed PS/2 Mouse Boot Summary ScreenPress F1 to resume, F2 to Setup, F3 for previous Device IRQ conﬂictPS/2 Mouse Press F2 to enter SetupSystem Bios shadowed Video Bios shadowedPage Post Code Description Appendix B Bios Post CodesRecoverable Post Errors Terminal Post ErrorsPost Code Description Post Code Description Post Code Description Appendix B Bios Post Codes Page Serverboard Appendix C System SpeciﬁcationsSystem Input Requirements WeightPower Supply System CoolingAppendix C System Speciﬁcations