SUPER MICRO Computer 6015TC-T, 6015TC-10G manual Server Chassis Features

Page 13

Chapter 1: Introduction

1-3 Server Chassis Features

The following is a general outline of the main features of the SC808T-780 1U chas- sis. Details on the chassis can be found in Chapter 6.

System Power

When conﬁgured as a SuperServer 6015TC-T/6015TC-10G, the SC808T-780 in- cludes a single 780W cold-swap power supply, which provides the power to both serverboards housed in the chassis.

SATA Subsystem

The SC808T-780 chassis was designed to support four SATA hard drives, which are hot-swappable units.

Control Panel

The SC808T-780 features two independant control panels associated with each serverboard in the chassis. Each control panel has LEDs to indicate power on, net- work activity, hard disk drive activity and system overheat conditions. Each control panel also includes a main power button and a system reset button.

Rear I/O Panel

The SC808T-780 is a 1U rackmount chassis. Its I/O panel provides a slots for two low-proﬁle PCI-E x16 expansion cards, two COM ports, four USB ports, two VGA ports and four Gb Ethernet ports. The 6015TC-10G also provides two 10 Gigabit Ethernet ports. See Chapter 6 for details.

Cooling System

The SC808T-780 chassis has an innovative cooling design that features two sets of triple (for a total of six) 4-cm high-performance fans. A fan speed control setting in BIOS allows fan speed to be determined by system temperature.

1-5

Image 13

Contents Super Manual Revision 1.0a Release Date November 11 About This Manual PrefaceManual Organization Advanced Serverboard Setup System SafetyAdvanced Chassis Setup BiosPreface Table of Contents System Interface Bios Overview Chapter IntroductionProcessors Memory Serverboard FeaturesSerial ATA PCI Expansion SlotsATI Graphics Controller Other FeaturesOnboard Controllers/Ports Intel 5100 Chipset System Block Diagram Server Chassis Features Sata Backplane/Drives 1U Twin System NotesHeadquarters Contacting SupermicroEurope Asia-PaciﬁcPage Preparing for Setup Chapter Server InstallationChoosing a Setup Location Unpacking the SystemPage Rack Mounting Considerations Ambient Operating TemperatureInstalling the Inner Rails Installing the System into a RackIdentifying the Sections of the Rack Rails Installing the Rack Rails Installing the Outer RailsInstalling the Server into the Rack Checking the Serverboard SetupInstalling the Server into a Telco Rack Accessing the Inside of the SystemChecking the Components and Setup Installing the Server into a RackProviding Power Preparing to Power OnChecking the Sata drives Checking the AirﬂowAccessing the Inside of the System Page Power ResetChapter System Interface Control Panel ButtonsOverheat/Fan Fail Control Panel LEDsSata Drive Carrier LEDs Page Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsPrecautions Chapter Advanced Serverboard SetupHandling the Serverboard Unpacking Serverboard InstallationCheck Compatibility of Serverboard Ports and I/O Shield Mounting the Serverboard onto the Serverboard TrayConnecting Data Cables Connecting CablesConnecting Power Cables I/O Ports Connecting the Control PanelInstalling the Processor Processor and Heatsink InstallationCPU installed in socket PnP cap released From load plate Removing the Heatsink Installing the HeatsinkInstalling Memory Modules Installing MemoryMemory Support Adding PCI Cards PCI Card InstallationPCI-Express Slot X7DCT-10G Layout Serverboard DetailsConnector Description Jumper Description Default SettingX7DCT/X7DCT-10G Quick Reference ATX Power Connector Connector DeﬁnitionsAuxiliary Power Connector Pwon ConnectorOverheat LED OH Power On LEDFan Headers NMI ButtonUniversal Serial Bus USB Serial Ports I2C Power ConnectorSgpio Header LAN1/2 Ethernet PortsVGA Enable/Disable Jumper SettingsCmos Clear To Clear CmosGb LAN Enable/Disable LAN1/LAN2 Enable/DisableWatch Dog Enable/Disable Gb LAN LED Indicator LED2 Onboard IndicatorsOnboard Power LED LED3 LAN1/LAN2 LEDsInstalling Additional Drivers 13 Conﬁguring Supero Doctor Advanced Serverboard Setup Page Chapter Advanced Chassis Setup Chassis Front View Control PanelAccessing the Drive Bays Drive Bay Installation/RemovalSystem Fans System Fan FailureMounting a Drive in a Carrier Installing/Removing Hot-swap Sata DrivesPower Supply Failure Power SupplyReplacing the Power Supply Removing the Power SupplyRemoving the Power Supply How To Change the Conﬁguration Data System BiosStarting the Setup Utility ChapterMain Bios Setup Running SetupDefault settings are in bold text unless otherwise noted Press the Delete key to enter SetupBios Date Main Bios Setup Menu Main Setup FeaturesSystem Time System DateType Sata Port1, Sata Port2, Sata Port3 and Sata Port4LBA Format Total SectorsTransfer Mode LBA Mode ControlUltra DMA Mode Native Mode OperationXBoot Features Advanced SetupPost Errors QuietBoot ModeAcpi Mode XMemory Cache Cache Base 512K-640K Cache Base 0-512KCache Extended Memory Discrete Mtrr AllocationXPCI-Exp Xpci ConﬁgurationXAdvanced Chipset Control Patrol Scrubbing Enable Multi-Media TimerDemand Scrubbing USB Host ControllerC1 Enhanced Mode Available if supported by the CPU Machine Checking Available when supported by the CPUHardware Prefetcher Available when supported by the CPU XI/O Device Conﬁguration Xcpu Cache ControlXdmi Event Logging XConsole Redirection Fan1-Fan3 XHardware Monitor LogicFan Speed Control Modes Voltage MonitoringFirmware Version Ipmi Speciﬁcation VersionSystem Event Logging Clear System Event LoggingXSystem Event Log/System Event Log List Mode XRealtime Sensor Data SecurityUser Password Is Supervisor Password IsSet Supervisor Password Set User PasswordPassword on Boot BootBoot Priority Order/Excluded from Boot Orders Exit Load Setup DefaultsExit Saving Changes Exit Discarding ChangesSave Changes Appendix a Bios Post Messages System timer error System Cmos checksum bad Default conﬁguration usedReal time clock error Check date and time settingsAllocation Error for device Fail-Safe Timer NMI FailedEntering Setup Eisa Cmos not writeablePress F1 to resume, F2 to Setup, F3 for previous PS/2 Mouse Boot Summary ScreenDevice IRQ conﬂict Nnnn kB Extended RAM PassedSystem Bios shadowed Press F2 to enter SetupVideo Bios shadowed PS/2 MousePage Recoverable Post Errors Appendix B Bios Post CodesTerminal Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Appendix B Bios Post Codes Page Serverboard Appendix C System SpeciﬁcationsPower Supply WeightSystem Cooling System Input RequirementsAppendix C System Speciﬁcations