SUPER MICRO Computer 6015TC-10G, 6015TC-T manual Control Panel LEDs, Overheat/Fan Fail

Page 28

SUPERSERVER 6015TC-T/6015TC-10G User's Manual

3-3 Control Panel LEDs

Each of the two control panels located on the front of the SC808T-780 chassis has ﬁve LEDs. Each LED provides you with critical information related its own speciﬁc serverboard. This section explains what each LED indicates when illuminated and any corrective action you may need to take.

Overheat/Fan Fail

When this LED ﬂashes, it indicates a fan failure. When on continuously it indicates an overheat condition, which may be caused by cables obstructing the airﬂow in the system or the ambient room temperature being too warm. Check the routing of the cables and make sure all fans are present and operating normally. You should also check to make sure that the chassis covers are installed. Finally, verify that the heatsinks are installed properly (see Chapter 5). This LED will remain ﬂashing or on as long as the indicated condition exists.

2

NIC2

Indicates network activity on LAN2 when ﬂashing

1

NIC1

Indicates network activity on LAN1 when ﬂashing.

HDD

Channel activity for the hard disk drives. This light indicates SATA drive activity on the 6015TC-T/6015TC-10G when ﬂashing.

3-2

Image 28

Contents Super Manual Revision 1.0a Release Date November 11 About This Manual PrefaceManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Interface Bios Chapter Introduction OverviewServerboard Features Processors MemorySerial ATA PCI Expansion SlotsATI Graphics Controller Other FeaturesOnboard Controllers/Ports Intel 5100 Chipset System Block Diagram Server Chassis Features 1U Twin System Notes Sata Backplane/DrivesContacting Supermicro HeadquartersEurope Asia-PaciﬁcPage Chapter Server Installation Preparing for SetupChoosing a Setup Location Unpacking the SystemPage Ambient Operating Temperature Rack Mounting ConsiderationsInstalling the Inner Rails Installing the System into a RackIdentifying the Sections of the Rack Rails Installing the Outer Rails Installing the Rack RailsChecking the Serverboard Setup Installing the Server into the RackInstalling the Server into a Telco Rack Accessing the Inside of the SystemInstalling the Server into a Rack Checking the Components and SetupPreparing to Power On Providing PowerChecking the Sata drives Checking the AirﬂowAccessing the Inside of the System Page Reset PowerChapter System Interface Control Panel ButtonsControl Panel LEDs Overheat/Fan FailSata Drive Carrier LEDs Page Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryPrecautions Chapter Advanced Serverboard SetupHandling the Serverboard Serverboard Installation UnpackingCheck Compatibility of Serverboard Ports and I/O Shield Mounting the Serverboard onto the Serverboard TrayConnecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel I/O PortsProcessor and Heatsink Installation Installing the ProcessorCPU installed in socket PnP cap released From load plate Installing the Heatsink Removing the HeatsinkInstalling Memory Modules Installing MemoryMemory Support Adding PCI Cards PCI Card InstallationPCI-Express Slot Serverboard Details X7DCT-10G LayoutConnector Description Jumper Description Default SettingX7DCT/X7DCT-10G Quick Reference Connector Deﬁnitions ATX Power ConnectorAuxiliary Power Connector Pwon ConnectorPower On LED Overheat LED OHFan Headers NMI ButtonUniversal Serial Bus USB I2C Power Connector Serial PortsSgpio Header LAN1/2 Ethernet PortsJumper Settings VGA Enable/DisableCmos Clear To Clear CmosGb LAN Enable/Disable LAN1/LAN2 Enable/DisableWatch Dog Enable/Disable Onboard Indicators Gb LAN LED Indicator LED2Onboard Power LED LED3 LAN1/LAN2 LEDsInstalling Additional Drivers 13 Conﬁguring Supero Doctor Advanced Serverboard Setup Page Chapter Advanced Chassis Setup Control Panel Chassis Front ViewDrive Bay Installation/Removal Accessing the Drive BaysSystem Fans System Fan FailureInstalling/Removing Hot-swap Sata Drives Mounting a Drive in a CarrierPower Supply Power Supply FailureReplacing the Power Supply Removing the Power SupplyRemoving the Power Supply System Bios How To Change the Conﬁguration DataStarting the Setup Utility ChapterRunning Setup Main Bios SetupDefault settings are in bold text unless otherwise noted Press the Delete key to enter SetupMain Bios Setup Menu Main Setup Features Bios DateSystem Time System DateSata Port1, Sata Port2, Sata Port3 and Sata Port4 TypeLBA Format Total SectorsLBA Mode Control Transfer ModeUltra DMA Mode Native Mode OperationAdvanced Setup XBoot FeaturesPost Errors QuietBoot ModeAcpi Mode XMemory Cache Cache Base 0-512K Cache Base 512K-640KCache Extended Memory Discrete Mtrr AllocationXpci Conﬁguration XPCI-ExpXAdvanced Chipset Control Enable Multi-Media Timer Patrol ScrubbingDemand Scrubbing USB Host ControllerC1 Enhanced Mode Available if supported by the CPU Machine Checking Available when supported by the CPUHardware Prefetcher Available when supported by the CPU Xcpu Cache Control XI/O Device ConﬁgurationXdmi Event Logging XConsole Redirection XHardware Monitor Logic Fan1-Fan3Fan Speed Control Modes Voltage MonitoringIpmi Speciﬁcation Version Firmware VersionSystem Event Logging Clear System Event LoggingXSystem Event Log/System Event Log List Mode Security XRealtime Sensor DataSupervisor Password Is User Password IsSet Supervisor Password Set User PasswordPassword on Boot BootBoot Priority Order/Excluded from Boot Orders Load Setup Defaults ExitExit Saving Changes Exit Discarding ChangesSave Changes Appendix a Bios Post Messages System Cmos checksum bad Default conﬁguration used System timer errorReal time clock error Check date and time settingsFail-Safe Timer NMI Failed Allocation Error for deviceEntering Setup Eisa Cmos not writeablePS/2 Mouse Boot Summary Screen Press F1 to resume, F2 to Setup, F3 for previousDevice IRQ conﬂict Nnnn kB Extended RAM PassedPress F2 to enter Setup System Bios shadowedVideo Bios shadowed PS/2 MousePage Appendix B Bios Post Codes Recoverable Post ErrorsTerminal Post Errors Post Code DescriptionPost Code Description Post Code Description Post Code Description Appendix B Bios Post Codes Page Appendix C System Speciﬁcations ServerboardWeight Power SupplySystem Cooling System Input RequirementsAppendix C System Speciﬁcations