SMC Networks SMC6724L2 manual Status LEDs, Port and System LEDs

Page 18

ABOUT THE TIGERSWITCH 10/100

Status LEDs

The LEDs, which are located on the front panel for easy viewing, are shown below and described in the following table.

Figure 1-4. Port and System LEDs

Port and System Status LEDs

LED

 

Condition

Status

 

 

 

 

Power

 

On

Switch is receiving power.

 

 

 

 

RJ-45 Ports

 

 

 

 

 

Link &

 

On

Port has established a valid network

Activity

 

 

connection.

 

 

 

 

 

 

Yellow

Valid 10 Mbps connection.

 

 

 

 

 

 

Green

Valid 100 Mbps connection.

 

 

 

 

 

 

Flashing

Traffic is passing through the port.

 

 

 

 

FDX

 

On

Port is operating at full duplex.

 

 

 

 

HDX

 

Off

Port is operating at half duplex.

 

 

 

 

Module Ports

 

 

 

 

 

Link &

 

On

A module is installed in this slot.

Activity

 

 

 

 

Yellow

Communications have been set to 1000

 

 

 

 

 

Mbps.

 

 

 

 

 

 

Flashing

Traffic is passing through the module.

 

 

 

 

1-4

Image 18
Contents TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty Limited Warranty Compliances FCC Class aEC Conformance Declaration Class a Industry Canada Class a Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety ComplianceIii Underwriters Laboratories Compliance StatementWichtige Sicherheitshinweise Germany Table of Contents Installing the Switch TroubleshootingMaking Network Connections Vii Viii Chapter About Tigerswitch 10/100 OverviewSwitch Architecture Management OptionsDescription of Hardware 10BASE-T/100BASE-TX Ports SMC6724L2Status LEDs Port and System LEDsSwitch Management Spanning Tree ProtocolMulticast Switching VLANsTraffic Priority Power Supply Receptacle Optional Media Extender ModuleOptional 1000BASE-SX Module SMC6724L2GSSC Features and Benefits ConnectivityExpandability Performance ManagementAbout the Tigerswitch 10/100 Introduction to Switching Chapter Network PlanningSample Applications Collapsed BackboneRemote Connections with Fiber Cable Making Vlan ConnectionsMaking Vlan Connections Connectivity Rules Mbps Gigabit Ethernet Collision DomainMbps Fast Ethernet Collision Domain Maximum Fast Ethernet Cable Distance Maximum Network Diameter Using RepeatersMbps Ethernet Collision Domain SMC 5-4-3 RuleApplication Notes Network Planning Installing the Switch Selecting a SiteEquipment Checklist Package ContentsOptional Rack-Mounting Equipment Mounting Rack MountingAttaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive FeetConnecting to a Power Source Power ReceptacleTwisted-Pair Devices Connecting Network DevicesChapter Making Network Connections Cabling GuidelinesCrossover/Straight-Through Wiring Requirement Connecting to PCs, Servers, Hubs and Switches Making Twisted-Pair ConnectionsWiring Closet Connections Wiring Closet ConnectionsFiber Optic Devices Making SC Port Connections Appendix a Troubleshooting Diagnosing Switch IndicatorsPower and Cooling Problems InstallationIn-Band Access Troubleshooting Troubleshooting Specifications Appendix B CablesFigure B-1. RJ-45 Connector Pin Numbers Twisted-Pair Cable and Pin AssignmentsStraight-Through Wiring 100BASE-TX/10BASE-T Pin AssignmentsCrossover Wiring Console Port Pin Assignments Figure B-2. DB-9 Console Port Pin NumbersDB-9 Port Pin Assignments Console Port to 9-Pin COM Port on PCConsole Port to 25-Pin DCE Port on Modem Console Port to 25-Pin DTE Port on PC Cables Appendix C Specifications Physical CharacteristicsPower Supply WeightTemperature Power ConsumptionSwitch Features Management Features Warranty StandardsCompliances Model Slide-in Module1000BASE-SX Extender Module StandardsAppendix D Ordering Information Ordering Information Auto-Negotiation GlossaryGlossary-1 BandwidthGlossary-2 Glossary-3 Glossary-4 Glossary-5 RJ-45 ConnectorSwitched Ports Network DiameterGlossary-6 Index Index-1Index-2 Index-3 Index-4 Page Internet