SMC Networks SMC6724L2 manual Making SC Port Connections

Page 44

MAKING NETWORK CONNECTIONS

Figure 4-3. Making SC Port Connections

4.As a connection is made, check the Activity LED on the switch’s front panel for the corresponding module to be sure that the connection is valid.

Note: If you use the optional SC-ST Converter, be sure to connect the converter’s Tx (Rx) port to the Rx (Tx) port on the other device.

The 1000BASE-SX fiber optic ports operate at 1 Gbps full duplex, with auto-negotiation of flow control. The maximum length for fiber optic cable operating at Gigabit speed will depend on the fiber type as listed under “1000 Mbps Gigabit Ethernet Collision Domain” on page 2-5.

4-6

Image 44

Contents TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty Limited Warranty EC Conformance Declaration Class a CompliancesFCC Class a Industry Canada Class a Safety Compliance IiiWarnhinweis Faseroptikanschlüsse Optische Sicherheit Underwriters Laboratories Compliance StatementWichtige Sicherheitshinweise Germany Table of Contents Making Network Connections Installing the SwitchTroubleshooting Vii Viii Chapter About Tigerswitch 10/100 OverviewSwitch Architecture Management OptionsDescription of Hardware 10BASE-T/100BASE-TX Ports SMC6724L2Status LEDs Port and System LEDsSwitch Management Spanning Tree ProtocolTraffic Priority Multicast SwitchingVLANs Optional 1000BASE-SX Module SMC6724L2GSSC Power Supply ReceptacleOptional Media Extender Module Expandability Features and BenefitsConnectivity Performance ManagementAbout the Tigerswitch 10/100 Introduction to Switching Chapter Network PlanningSample Applications Collapsed BackboneRemote Connections with Fiber Cable Making Vlan ConnectionsMaking Vlan Connections Mbps Fast Ethernet Collision Domain Connectivity RulesMbps Gigabit Ethernet Collision Domain Maximum Network Diameter Using Repeaters Mbps Ethernet Collision DomainMaximum Fast Ethernet Cable Distance SMC 5-4-3 RuleApplication Notes Network Planning Installing the Switch Selecting a SiteOptional Rack-Mounting Equipment Equipment ChecklistPackage Contents Mounting Rack MountingAttaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive FeetConnecting to a Power Source Power ReceptacleConnecting Network Devices Chapter Making Network ConnectionsTwisted-Pair Devices Cabling GuidelinesCrossover/Straight-Through Wiring Requirement Connecting to PCs, Servers, Hubs and Switches Making Twisted-Pair ConnectionsWiring Closet Connections Wiring Closet ConnectionsFiber Optic Devices Making SC Port Connections Appendix a Troubleshooting Diagnosing Switch IndicatorsIn-Band Access Power and Cooling ProblemsInstallation Troubleshooting Troubleshooting Specifications Appendix B CablesFigure B-1. RJ-45 Connector Pin Numbers Twisted-Pair Cable and Pin AssignmentsStraight-Through Wiring 100BASE-TX/10BASE-T Pin AssignmentsCrossover Wiring Console Port Pin Assignments Figure B-2. DB-9 Console Port Pin NumbersConsole Port to 25-Pin DCE Port on Modem DB-9 Port Pin AssignmentsConsole Port to 9-Pin COM Port on PC Console Port to 25-Pin DTE Port on PC Cables Appendix C Specifications Physical CharacteristicsWeight TemperaturePower Supply Power ConsumptionSwitch Features Management Features Compliances WarrantyStandards Slide-in Module 1000BASE-SX Extender ModuleModel StandardsAppendix D Ordering Information Ordering Information Glossary Glossary-1Auto-Negotiation BandwidthGlossary-2 Glossary-3 Glossary-4 RJ-45 Connector Switched PortsGlossary-5 Network DiameterGlossary-6 Index Index-1Index-2 Index-3 Index-4 Page Internet