SMC Networks SMC6724L2 manual Connecting to a Power Source, Power Receptacle

Page 38

INSTALLING THE SWITCH

Connecting to a Power Source

To connect a device to a power source:

1.Insert the power cable plug directly into the receptacle located at the back of the device.

Figure 3-4. Power Receptacle

2. Plug the other end of the cable into a grounded, 3-pin socket.

Note: For International use, you may need to change the AC line cord. You must use a line cord set that has been approved for the receptacle type in your country.

3.Check the front-panel LEDs as the device is powered on to be sure the Power LED is lit. If not, check that the power cable is correctly plugged in.

3-6

Image 38

Contents TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty Limited Warranty EC Conformance Declaration Class a CompliancesFCC Class a Industry Canada Class a Warnhinweis Faseroptikanschlüsse Optische Sicherheit Safety ComplianceIii Underwriters Laboratories Compliance StatementWichtige Sicherheitshinweise Germany Table of Contents Making Network Connections Installing the SwitchTroubleshooting Vii Viii Chapter About Tigerswitch 10/100 OverviewSwitch Architecture Management OptionsDescription of Hardware 10BASE-T/100BASE-TX Ports SMC6724L2Status LEDs Port and System LEDsSwitch Management Spanning Tree ProtocolTraffic Priority Multicast SwitchingVLANs Optional 1000BASE-SX Module SMC6724L2GSSC Power Supply ReceptacleOptional Media Extender Module Expandability Features and BenefitsConnectivity Performance ManagementAbout the Tigerswitch 10/100 Introduction to Switching Chapter Network PlanningSample Applications Collapsed BackboneRemote Connections with Fiber Cable Making Vlan ConnectionsMaking Vlan Connections Mbps Fast Ethernet Collision Domain Connectivity RulesMbps Gigabit Ethernet Collision Domain Maximum Fast Ethernet Cable Distance Maximum Network Diameter Using RepeatersMbps Ethernet Collision Domain SMC 5-4-3 RuleApplication Notes Network Planning Installing the Switch Selecting a SiteOptional Rack-Mounting Equipment Equipment ChecklistPackage Contents Mounting Rack MountingAttaching the Brackets Desktop or Shelf Mounting Attaching the Adhesive FeetConnecting to a Power Source Power ReceptacleTwisted-Pair Devices Connecting Network DevicesChapter Making Network Connections Cabling GuidelinesCrossover/Straight-Through Wiring Requirement Connecting to PCs, Servers, Hubs and Switches Making Twisted-Pair ConnectionsWiring Closet Connections Wiring Closet ConnectionsFiber Optic Devices Making SC Port Connections Appendix a Troubleshooting Diagnosing Switch IndicatorsIn-Band Access Power and Cooling ProblemsInstallation Troubleshooting Troubleshooting Specifications Appendix B CablesFigure B-1. RJ-45 Connector Pin Numbers Twisted-Pair Cable and Pin AssignmentsStraight-Through Wiring 100BASE-TX/10BASE-T Pin AssignmentsCrossover Wiring Console Port Pin Assignments Figure B-2. DB-9 Console Port Pin NumbersConsole Port to 25-Pin DCE Port on Modem DB-9 Port Pin AssignmentsConsole Port to 9-Pin COM Port on PC Console Port to 25-Pin DTE Port on PC Cables Appendix C Specifications Physical CharacteristicsPower Supply WeightTemperature Power ConsumptionSwitch Features Management Features Compliances WarrantyStandards Model Slide-in Module1000BASE-SX Extender Module StandardsAppendix D Ordering Information Ordering Information Auto-Negotiation GlossaryGlossary-1 BandwidthGlossary-2 Glossary-3 Glossary-4 Glossary-5 RJ-45 ConnectorSwitched Ports Network DiameterGlossary-6 Index Index-1Index-2 Index-3 Index-4 Page Internet