SMC Networks SMC6724L2 manual Desktop or Shelf Mounting, Attaching the Adhesive Feet

Page 37

INSTALLING THE SWITCH

3.If installing a single switch only, turn to “Connecting to a Power Source” at the end of this chapter.

4.If installing multiple switches, mount them in the rack, one below the other, in any order.

Desktop or Shelf Mounting

1. Attach the four adhesive feet to the bottom of the first switch.

Figure 3-3. Attaching the Adhesive Feet

2.Set the device on a flat surface near an AC power source, making sure there are at least two inches of space on all sides for proper air flow.

3.If installing a single switch only, go to “Connecting to a Power Source” at the end of this chapter.

4.If installing multiple switches, attach four adhesive feet to each one. Place each device squarely on top of the one below, in any order.

3-5

Image 37
Contents TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty Limited Warranty FCC Class a CompliancesEC Conformance Declaration Class a Industry Canada Class a Iii Safety ComplianceWarnhinweis Faseroptikanschlüsse Optische Sicherheit Underwriters Laboratories Compliance StatementWichtige Sicherheitshinweise Germany Table of Contents Troubleshooting Installing the SwitchMaking Network Connections Vii Viii Overview Chapter About Tigerswitch 10/100Management Options Switch Architecture10BASE-T/100BASE-TX Ports SMC6724L2 Description of HardwarePort and System LEDs Status LEDsSpanning Tree Protocol Switch ManagementVLANs Multicast SwitchingTraffic Priority Optional Media Extender Module Power Supply ReceptacleOptional 1000BASE-SX Module SMC6724L2GSSC Connectivity Features and BenefitsExpandability Management PerformanceAbout the Tigerswitch 10/100 Chapter Network Planning Introduction to SwitchingCollapsed Backbone Sample ApplicationsMaking Vlan Connections Remote Connections with Fiber CableMaking Vlan Connections Mbps Gigabit Ethernet Collision Domain Connectivity RulesMbps Fast Ethernet Collision Domain Mbps Ethernet Collision Domain Maximum Network Diameter Using RepeatersMaximum Fast Ethernet Cable Distance SMC 5-4-3 RuleApplication Notes Network Planning Selecting a Site Installing the SwitchPackage Contents Equipment ChecklistOptional Rack-Mounting Equipment Rack Mounting MountingAttaching the Brackets Attaching the Adhesive Feet Desktop or Shelf MountingPower Receptacle Connecting to a Power SourceChapter Making Network Connections Connecting Network DevicesTwisted-Pair Devices Cabling GuidelinesCrossover/Straight-Through Wiring Requirement Making Twisted-Pair Connections Connecting to PCs, Servers, Hubs and SwitchesWiring Closet Connections Wiring Closet ConnectionsFiber Optic Devices Making SC Port Connections Diagnosing Switch Indicators Appendix a TroubleshootingInstallation Power and Cooling ProblemsIn-Band Access Troubleshooting Troubleshooting Appendix B Cables SpecificationsTwisted-Pair Cable and Pin Assignments Figure B-1. RJ-45 Connector Pin Numbers100BASE-TX/10BASE-T Pin Assignments Straight-Through WiringCrossover Wiring Figure B-2. DB-9 Console Port Pin Numbers Console Port Pin AssignmentsConsole Port to 9-Pin COM Port on PC DB-9 Port Pin AssignmentsConsole Port to 25-Pin DCE Port on Modem Console Port to 25-Pin DTE Port on PC Cables Physical Characteristics Appendix C SpecificationsTemperature WeightPower Supply Power ConsumptionSwitch Features Management Features Standards WarrantyCompliances 1000BASE-SX Extender Module Slide-in ModuleModel StandardsAppendix D Ordering Information Ordering Information Glossary-1 GlossaryAuto-Negotiation BandwidthGlossary-2 Glossary-3 Glossary-4 Switched Ports RJ-45 ConnectorGlossary-5 Network DiameterGlossary-6 Index-1 IndexIndex-2 Index-3 Index-4 Page Internet