SMC Networks SMC6724L2 manual Connecting to PCs, Servers, Hubs and Switches

Page 41

MAKING NETWORK CONNECTIONS

Connecting to PCs, Servers, Hubs and Switches

1.Attach one end of a twisted-pair cable segment to the device’s RJ-45 connector.

Figure 4-1. Making Twisted-Pair Connections

2.If the device is a network card and the TigerSwitch is in the wiring closet, attach the other end of the cable segment to a modular wall outlet that is connected to the wiring closet (see “Wiring Closet Connections” on the next page). Otherwise, attach the other end to an available port on the switch.

3.If the device is a hub or switch, use the cable type indicated under “Cabling Guidelines” on page 4-1, and attach the other end to a port on the TigerSwitch.

4.Make sure each twisted pair cable does not exceed 100 meters (328 ft.) in length.

Note: When connected to a shared collision domain (such as a hub with multiple workstations), switch ports must be set to half-duplex mode and back pressure flow control disabled.

4-3

Image 41

Contents TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty Limited Warranty EC Conformance Declaration Class a CompliancesFCC Class a Industry Canada Class a Iii Safety ComplianceWarnhinweis Faseroptikanschlüsse Optische Sicherheit Underwriters Laboratories Compliance StatementWichtige Sicherheitshinweise Germany Table of Contents Making Network Connections Installing the SwitchTroubleshooting Vii Viii Overview Chapter About Tigerswitch 10/100Management Options Switch Architecture10BASE-T/100BASE-TX Ports SMC6724L2 Description of HardwarePort and System LEDs Status LEDsSpanning Tree Protocol Switch ManagementTraffic Priority Multicast SwitchingVLANs Optional 1000BASE-SX Module SMC6724L2GSSC Power Supply ReceptacleOptional Media Extender Module Expandability Features and BenefitsConnectivity Management PerformanceAbout the Tigerswitch 10/100 Chapter Network Planning Introduction to SwitchingCollapsed Backbone Sample ApplicationsMaking Vlan Connections Remote Connections with Fiber CableMaking Vlan Connections Mbps Fast Ethernet Collision Domain Connectivity RulesMbps Gigabit Ethernet Collision Domain Mbps Ethernet Collision Domain Maximum Network Diameter Using RepeatersMaximum Fast Ethernet Cable Distance SMC 5-4-3 RuleApplication Notes Network Planning Selecting a Site Installing the SwitchOptional Rack-Mounting Equipment Equipment ChecklistPackage Contents Rack Mounting MountingAttaching the Brackets Attaching the Adhesive Feet Desktop or Shelf MountingPower Receptacle Connecting to a Power SourceChapter Making Network Connections Connecting Network DevicesTwisted-Pair Devices Cabling GuidelinesCrossover/Straight-Through Wiring Requirement Making Twisted-Pair Connections Connecting to PCs, Servers, Hubs and SwitchesWiring Closet Connections Wiring Closet ConnectionsFiber Optic Devices Making SC Port Connections Diagnosing Switch Indicators Appendix a TroubleshootingIn-Band Access Power and Cooling ProblemsInstallation Troubleshooting Troubleshooting Appendix B Cables SpecificationsTwisted-Pair Cable and Pin Assignments Figure B-1. RJ-45 Connector Pin Numbers100BASE-TX/10BASE-T Pin Assignments Straight-Through WiringCrossover Wiring Figure B-2. DB-9 Console Port Pin Numbers Console Port Pin AssignmentsConsole Port to 25-Pin DCE Port on Modem DB-9 Port Pin AssignmentsConsole Port to 9-Pin COM Port on PC Console Port to 25-Pin DTE Port on PC Cables Physical Characteristics Appendix C SpecificationsTemperature WeightPower Supply Power ConsumptionSwitch Features Management Features Compliances WarrantyStandards 1000BASE-SX Extender Module Slide-in ModuleModel StandardsAppendix D Ordering Information Ordering Information Glossary-1 GlossaryAuto-Negotiation BandwidthGlossary-2 Glossary-3 Glossary-4 Switched Ports RJ-45 ConnectorGlossary-5 Network DiameterGlossary-6 Index-1 IndexIndex-2 Index-3 Index-4 Page Internet