SMC Networks SMC6724L2 manual Installing the Switch, Selecting a Site

Page 33

CHAPTER 3 INSTALLING THE SWITCH

Selecting a Site

TigerSwitch 10/100 units can be mounted in a standard 19-inch equipment rack or on a flat surface. Be sure to follow the guidelines below when choosing a location.

◆The site should:

•be at the center of all the devices you want to link and near a power outlet.

•be able to maintain its temperature within 0° to 50° C and its humidity within 5% to 95%, non-condensing

•provide adequate space (approximately two inches) on all sides for proper air flow

•be accessible for installing, cabling and maintaining the devices

•allow the status LEDs to be clearly visible

◆Make sure twisted-pair cable is always routed away from power lines, fluorescent lighting fixtures and other sources of electrical interference, such as radios, transmitters, etc.

◆Make sure that a separate grounded power outlet that provides 100 to 240 VAC, 50 to 60 Hz, is within 8 feet of each device and is powered from an independent circuit breaker. As with any equipment, using a filter or surge suppressor is recommended.

3-1

Image 33

Contents TigerSwitch 10/100 Page TigerSwitch 10/100 Installation Guide Trademarks Limited Warranty Limited Warranty Compliances FCC Class aEC Conformance Declaration Class a Industry Canada Class a Iii Safety ComplianceWarnhinweis Faseroptikanschlüsse Optische Sicherheit Underwriters Laboratories Compliance StatementWichtige Sicherheitshinweise Germany Table of Contents Installing the Switch TroubleshootingMaking Network Connections Vii Viii Overview Chapter About Tigerswitch 10/100Management Options Switch Architecture10BASE-T/100BASE-TX Ports SMC6724L2 Description of HardwarePort and System LEDs Status LEDsSpanning Tree Protocol Switch ManagementMulticast Switching VLANsTraffic Priority Power Supply Receptacle Optional Media Extender ModuleOptional 1000BASE-SX Module SMC6724L2GSSC Features and Benefits ConnectivityExpandability Management PerformanceAbout the Tigerswitch 10/100 Chapter Network Planning Introduction to SwitchingCollapsed Backbone Sample ApplicationsMaking Vlan Connections Remote Connections with Fiber CableMaking Vlan Connections Connectivity Rules Mbps Gigabit Ethernet Collision DomainMbps Fast Ethernet Collision Domain Mbps Ethernet Collision Domain Maximum Network Diameter Using RepeatersMaximum Fast Ethernet Cable Distance SMC 5-4-3 RuleApplication Notes Network Planning Selecting a Site Installing the SwitchEquipment Checklist Package ContentsOptional Rack-Mounting Equipment Rack Mounting MountingAttaching the Brackets Attaching the Adhesive Feet Desktop or Shelf MountingPower Receptacle Connecting to a Power SourceChapter Making Network Connections Connecting Network DevicesTwisted-Pair Devices Cabling GuidelinesCrossover/Straight-Through Wiring Requirement Making Twisted-Pair Connections Connecting to PCs, Servers, Hubs and SwitchesWiring Closet Connections Wiring Closet ConnectionsFiber Optic Devices Making SC Port Connections Diagnosing Switch Indicators Appendix a TroubleshootingPower and Cooling Problems InstallationIn-Band Access Troubleshooting Troubleshooting Appendix B Cables SpecificationsTwisted-Pair Cable and Pin Assignments Figure B-1. RJ-45 Connector Pin Numbers100BASE-TX/10BASE-T Pin Assignments Straight-Through WiringCrossover Wiring Figure B-2. DB-9 Console Port Pin Numbers Console Port Pin AssignmentsDB-9 Port Pin Assignments Console Port to 9-Pin COM Port on PCConsole Port to 25-Pin DCE Port on Modem Console Port to 25-Pin DTE Port on PC Cables Physical Characteristics Appendix C SpecificationsTemperature WeightPower Supply Power ConsumptionSwitch Features Management Features Warranty StandardsCompliances 1000BASE-SX Extender Module Slide-in ModuleModel StandardsAppendix D Ordering Information Ordering Information Glossary-1 GlossaryAuto-Negotiation BandwidthGlossary-2 Glossary-3 Glossary-4 Switched Ports RJ-45 ConnectorGlossary-5 Network DiameterGlossary-6 Index-1 IndexIndex-2 Index-3 Index-4 Page Internet