Seagate ST3200826ACE Physical characteristics, Seek time, Start/stop times, Typical seek times

Page 16

2.4Physical characteristics

Drive specification

Maximum height

(mm)26.11

(inches) 1.028

Maximum width

(mm)101.85

(inches)

4.010 ± 0.010

 

Maximum length

(mm)146.99

(inches) 5.787

Typical weight

(grams)

635

(pounds)

1.39

2.5Seek time

Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows:

Track-to-track seek time is an average of all possible single-track seeks in both directions.

Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead.

Table 2:

Typical seek times

 

 

 

 

 

Typical seek times (msec)

Read

Write

 

 

 

Track-to-track

0.8

1.0

 

 

 

 

Average

 

18

20

 

 

 

Average latency:

4.16

4.16

 

 

 

 

Note. These drives are designed to consistently meet the seek times represented in this manual. Physical seeks, regardless of mode (such as track-to-track and average), are expected to meet or exceed the noted values. However, due to the manner in which these drives are formatted, benchmark tests that include command overhead or measure logical seeks may produce results that vary from these specifications.

2.6Start/stop times

Power-on to Ready (sec)

15.5 (max)

 

 

Standby to Ready (sec)

14.0 (max)

 

 

Ready to spindle stop (sec)

10 (max)

 

 

6

DB35 Series Product Manual, Rev. B

Image 16
Contents DB35 Series Page DB35 Series Page Revision status summary sheet DB35 Series Product Manual, Rev. B Contents DB35 Series Product Manual, Rev. B List of Figures Viii DB35 Series Product Manual, Rev. B Introduction DB35 SeriesDB35 Series Product Manual, Rev. B Specification summary table Drive specificationsDrive specifications Altitude, nonoperating To 12,192 m Below mean sea level, max Formatted capacity LBA modeRecording and interface technology Physical characteristics Seek timeStart/stop times Typical seek timesPower specifications Conducted noise Typical current profileVoltage tolerance Environmental specifications Temperature gradient Wet bulb temperatureHumidity Relative humidity AltitudeAcoustics Electromagnetic immunityNonoperating vibration Operating acousticsSafety certification ReliabilityAgency certification Electromagnetic compatibilityEnvironmental protection Australian C-Tick N176FCC verification European Union Restriction of Hazardous Substances RoHSDB35 Series Product Manual, Rev. B Configuring and mounting the drive Handling and static discharge precautionsBreather filter hole precautions Breather filter hole locationJumper settings Master/slave configurationDrive as master with a non-ATA-compatible slave Cable-select optionDrive mounting Ultra ATA/100 cableMounting dimensions-top, side and end view DB35 Series Product Manual, Rev. B ATA interface signals and connector pins ATA interfaceSupported ATA commands Command name Command code in hexF6H Identify Device command Word Description ValueXxxxH Description if bit is set to Bit Word Set Features command 4 S.M.A.R.T. commandsCode in features Register A.R.T. command Seagate Technology support services Internet MySeagate Reseller.seagate.comPresales Support Technical SupportWarranty Service Authorized Service CentersCall Center Toll-free Direct dial Americas +1-405-324-47301 +1-405-324-4704Americas SEAGATE2 +1-405-324-47002 +1-405-324-3339 Call Center Toll-free Direct dial FAX / E-mailCall Center Presales and Technical Support Warranty Service FAX Services-All Europe toll callToll-Free Support Numbers Asia/Pacific Support Services DB35 Series Product Manual, Rev. B Index NumericsPage Page DB35 Series Product Manual, Rev. B Page Seagate Technology LLC