Seagate ST3300831ACE, ST3200826ACE, ST3250823ACE manual Code in features Register A.R.T. command

Page 38

SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4H) that elimi- nates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at: http://seatools.seagate.com.

This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the drive uses.

Code in features

 

register

S.M.A.R.T. command

 

 

D0H

S.M.A.R.T. Read Data

D1H

Vendor-specific

 

 

D2H

S.M.A.R.T. Enable/Disable Attribute Autosave

 

 

D3H

S.M.A.R.T. Save Attribute Values

 

 

D4H

S.M.A.R.T. Execute Off-line Immediate (runs DST)

 

 

D5H

S.M.A.R.T. Read Log Sector

 

 

D6H

S.M.A.R.T. Write Log Sector

 

 

D7H

Vendor-specific

 

 

D8H

S.M.A.R.T. Enable Operations

 

 

D9H

S.M.A.R.T. Disable Operations

 

 

DAH

S.M.A.R.T. Return Status

 

 

Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04 (abort) is written to the Error register.

28

DB35 Series Product Manual, Rev. B

Image 38
Contents DB35 Series Page DB35 Series Page Revision status summary sheet DB35 Series Product Manual, Rev. B Contents DB35 Series Product Manual, Rev. B List of Figures Viii DB35 Series Product Manual, Rev. B Introduction DB35 SeriesDB35 Series Product Manual, Rev. B Drive specifications Drive specificationsSpecification summary table Altitude, nonoperating To 12,192 m Below mean sea level, max Recording and interface technology LBA modeFormatted capacity Start/stop times Physical characteristicsSeek time Typical seek timesPower specifications Voltage tolerance Typical current profileConducted noise Environmental specifications Humidity Relative humidity Temperature gradientWet bulb temperature AltitudeNonoperating vibration AcousticsElectromagnetic immunity Operating acousticsAgency certification Safety certificationReliability Electromagnetic compatibilityFCC verification Environmental protectionAustralian C-Tick N176 European Union Restriction of Hazardous Substances RoHSDB35 Series Product Manual, Rev. B Configuring and mounting the drive Handling and static discharge precautionsBreather filter hole precautions Breather filter hole locationDrive as master with a non-ATA-compatible slave Jumper settingsMaster/slave configuration Cable-select optionDrive mounting Ultra ATA/100 cableMounting dimensions-top, side and end view DB35 Series Product Manual, Rev. B ATA interface signals and connector pins ATA interfaceSupported ATA commands Command name Command code in hexF6H Identify Device command Word Description ValueXxxxH Description if bit is set to Bit Word Set Features command 4 S.M.A.R.T. commandsCode in features Register A.R.T. command Presales Support Seagate Technology support servicesInternet MySeagate Reseller.seagate.com Technical SupportWarranty Service Authorized Service CentersAmericas SEAGATE2 +1-405-324-47002 +1-405-324-3339 Call Center Toll-free Direct dialAmericas +1-405-324-47301 +1-405-324-4704 Call Center Toll-free Direct dial FAX / E-mailToll-Free Support Numbers FAX Services-All Europe toll callCall Center Presales and Technical Support Warranty Service Asia/Pacific Support Services DB35 Series Product Manual, Rev. B Index NumericsPage Page DB35 Series Product Manual, Rev. B Page Seagate Technology LLC