Western Telematic IPS-800-D20, IPS-800E-D20, IPS-1600-D20, IPS-1600E-D20 manual

Page 16

IPS-800/1600-D20 Series - User’s Guide

IPS UNIT

POWER INLETS

BOTTOM

PLATE

SLIDER

SCREW PLATE RECEPTACLES

Figure 4.1: IPS-800 Series Cable Keeper Installation

4.Connect the power cables to the power inlets. Check to make sure that both cables are ﬁrmly seated in the power inlet connectors.

5.Align the power cables with the two notches in the top of the slider plate, and then move the slider plate forward until both cables are held ﬁrmly in place.

6.Tighten the two screws that secure the slider plate to the bottom plate. Check to make certain that the cables are held ﬁrmly in place by the cable keepers.

4.2.Connection to Switched Outlets

Connect the power cord from your switched device to one of the AC Outlets on the IPS unit. Note that when power is applied to the IPS, the AC Outlets will be switched "ON" by default.

•IPS-800-D20 and IPS-1600-D20 (120 VAC Models): Units include two separate power busses. Each bus can support a total of 20 Amps. Each AC Outlet can support up to 15 Amps.

•IPS-800E-D20 and IPS-1600E-D20 (230 VAC Models): Units include two separate power busses. Each bus can support a total of 20 Amps. Each AC Outlet can support up to 15 Amps.

4-2

Image 16

Contents User’s Guide ModelsPage Installation Instructions FCC Part 15 Regulation Table of Contents List of Figures Introduction IPS-800-D20, IPS-800E-D20, IPS-1600-D20 IPS-1600E-D20 Units Typographic ConventionsUnit Description IPS-800-D20 Back Panel 120 VAC Model ShownIPS-800/1600-D20 Series User’s Guide Apply Power to the IPS Hardware InstallationQuick Start Communicating with the IPS Connect your PC to the IPSText Interface Text Interface Type /X and press Enter Power Supply Connection InstallationInstalling the Cable Keepers Connection to Switched Outlets IPS-800 Series Cable Keeper InstallationConnecting the Network Cable Connecting a Local PCConnecting an External Modem Serial COM / RS232 Port ConnectionIPS-800/1600-D20 Series User’s Guide Configuration System Mode and User ModeAccessing the Web Browser Interface Plug Status Screen Web Browser Interface IPS-800-D20 ShownAccessing the Text Interface $ telnet 192.168.168.168 Enter Configuration Menus General Parameters Menus General Parameters Menu Web Browser InterfaceGeneral Parameters Menu Text Interface IPS-800/1600-D20 Series User’s Guide Serial Parameters Menu Serial ParametersIPS-800/1600-D20 Series User’s Guide Plug Parameters Menus Plug #1 ParametersPlug Passwords and Co-Location Features Reboot Cycles Network Parameters Menu Web Browser Interface Network Parameters Menus IP Security Feature Conﬁ guration Telnet Parameters Menus 12 Telnet Parameters Menu Web Browser InterfaceWeb Server Parameters Menus 14 Web Server Parameters Menu Web Browser InterfaceSave Configuration Parameters Operation via the Web Browser Interface OperationPlug Status Screen Web Browser Interface Plug Status Menu Web Browser Interface IPS-800-D20 Shown Operation via the Text Interface Plug Status Screen Text InterfaceSwitching and Reboot Commands Text Interface IPS Help Screen Text InterfaceBoot 1 or /BO Atmswtch Logging Out of Command Mode Applying Commands to Several Plugs Text InterfaceAutomated Mode Manual Operation Saving and Restoring Configuration Parameters Sending Parameters to a FileRestoring Saved Parameters Upgrading the IPS Firmware IPS-800/1600-D20 Series User’s Guide Serial COM / RS232 Port Interface Interface DescriptionApx-1 Specifications Apx-2Customer Service Apx-3Trademark and Copyright Information Apx-4Index Index-1Index-2 Page Sterling Irvine California 949 586-9950 Toll Free