Western Telematic IPS-800-D20, IPS-800E-D20, IPS-1600-D20, IPS-1600E-D20 manual

Page 42

IPS-800/1600-D20 Series - User’s Guide

Internet Power Switch v1.41h

Site ID: (undefined)

 

Display

 

Display Help Screen

 

 

Configuration

/H

 

 

 

 

/G

View/Set General Parameters

/S

 

 

Display Plug Status

 

 

/P [n]

View/Set Plug Parameters

/SN

 

 

Display Network Status

 

/C

View/Set Serial Parameters

Control

 

 

 

 

/N

View/Set Network Parameters

 

Set Plugs to Default

 

 

/T

View/set Telnet Parameters

/D

 

 

 

 

/W

View/Set Web Server

/Boot <n>

Boot Plug n

 

 

/E

Save Parameters

/On <n>

 

Turn On Plug n

 

 

/R

Recall Parameters

/Off <n>

Turn Off Plug n

 

 

/DL

Download Parameters to File

/X

 

 

Exit/Disconnect

 

 

Utilities

 

+------------------------------------

 

 

 

+

Reset Network Interface

 

 

 

/I

[n] =

optional plug name or number

/U

Upgrade Firmware

<n> =

required plug name or number

 

 

n+n or n n = plug n and plug n

 

 

 

n:n =

plug n through plug n

 

 

 

*

=

all plugs

 

 

 

,y

=

bypass “Sure? (y/n)”

 

 

 

+------------------------------------

 

 

 

+

 

 

IPS>

Figure 6.3: The IPS Help Screen - Text Interface

6.2.2.Switching and Reboot Commands - Text Interface

These commands can be used to switch or reboot the IPS’s switched plugs, and can also be used to set plugs to the user-defined Power-Up Default values. Plugs may be specified by name or number.

Notes:

Wait for the "IPS>" prompt to appear before entering commands. The prompt will not reappear until the previous command is complete.

Commands are not case sensitive. All commands are invoked by pressing [Enter].

Users who login to command mode using a Plug password, will only be allowed to issue commands to the plugs allowed by that password.

If command confirmation is enabled, the IPS will display the Status Screen after commands are successfully completed.

When switching and reboot operations are initiated, Boot/Sequence Delay times will be applied as described in Section 5.3.3.2.

6-4

Image 42
Contents User’s Guide ModelsPage Installation Instructions FCC Part 15 Regulation Table of Contents List of Figures Introduction IPS-800-D20, IPS-800E-D20, IPS-1600-D20 IPS-1600E-D20 Units Typographic ConventionsUnit Description IPS-800-D20 Back Panel 120 VAC Model ShownIPS-800/1600-D20 Series User’s Guide Hardware Installation Apply Power to the IPSQuick Start Communicating with the IPS Connect your PC to the IPSText Interface Text Interface Type /X and press Enter Installation Power Supply ConnectionInstalling the Cable Keepers Connection to Switched Outlets IPS-800 Series Cable Keeper InstallationConnecting an External Modem Connecting the Network CableConnecting a Local PC Serial COM / RS232 Port ConnectionIPS-800/1600-D20 Series User’s Guide Configuration System Mode and User ModeAccessing the Web Browser Interface Plug Status Screen Web Browser Interface IPS-800-D20 ShownAccessing the Text Interface $ telnet 192.168.168.168 Enter Configuration Menus General Parameters Menus General Parameters Menu Web Browser InterfaceGeneral Parameters Menu Text Interface IPS-800/1600-D20 Series User’s Guide Serial Parameters Menu Serial ParametersIPS-800/1600-D20 Series User’s Guide Plug Parameters Menus Plug #1 ParametersPlug Passwords and Co-Location Features Reboot Cycles Network Parameters Menu Web Browser Interface Network Parameters Menus IP Security Feature Confi guration Telnet Parameters Menus 12 Telnet Parameters Menu Web Browser InterfaceWeb Server Parameters Menus 14 Web Server Parameters Menu Web Browser InterfaceSave Configuration Parameters Operation Operation via the Web Browser InterfacePlug Status Screen Web Browser Interface Plug Status Menu Web Browser Interface IPS-800-D20 Shown Operation via the Text Interface Plug Status Screen Text InterfaceSwitching and Reboot Commands Text Interface IPS Help Screen Text InterfaceBoot 1 or /BO Atmswtch Logging Out of Command Mode Applying Commands to Several Plugs Text InterfaceAutomated Mode Manual Operation Saving and Restoring Configuration Parameters Sending Parameters to a FileRestoring Saved Parameters Upgrading the IPS Firmware IPS-800/1600-D20 Series User’s Guide Interface Description Serial COM / RS232 Port InterfaceApx-1 Specifications Apx-2Customer Service Apx-3Trademark and Copyright Information Apx-4Index Index-1Index-2 Page Sterling Irvine California 949 586-9950 Toll Free