NETGEAR DG814 DSL manual Gateway Upgrade menu

Page 67

Reference Manual for the Model DG814 DSL Modem Internet Gateway

Gateway Upgrade

The routing software of the Model DG814 gateway is stored in FLASH memory, and can be upgraded as new software is released by NETGEAR. Upgrade files can be downloaded from Netgear's website. If the upgrade file is compressed (.ZIP file), you must first extract the binary (.BIN) file before sending it to the gateway. The upgrade file can be sent to the gateway using your browser.

Note: The Web browser used to upload new firmware into the Model DG814 gateway must support HTTP uploads. NETGEAR recommends using Microsoft Internet Explorer or Netscape Navigator 3.0 or above.

From the Main Menu of the browser interface, under the Maintenance heading, select the Gateway Upgrade heading to display the menu shown in Figure 6-8.

Figure 6-8. Gateway Upgrade menu

To upload new firmware:

1.Download and unzip the new software file from NETGEAR.

2.In the Gateway Upgrade menu, click the Browse button and browse to the location of the binary (.BIN) upgrade file

3.Click Upload.

Note: When uploading software to the Model DG814 gateway, it is important not to interrupt the Web browser by closing the window, clicking a link, or loading a new page. If the browser is interrupted, it may corrupt the software. When the upload is complete, your gateway will automatically restart. The upgrade process will typically take about one minute.

In some cases, you may need to reconfigure the gateway after upgrading.

Maintenance

6-9

Image 67
Contents NETGEAR, Inc Trademarks World Wide Web Page Contents Chapter Preparing Your Network Chapter Maintenance Appendix a Technical Specifications Figure B-1 Page Table B-1 Xii Technical Support Related Publications About This GuideXiv About This Guide Special Message Formats Typographical ConventionsPage Chapter Introduction Key FeaturesAbout the Gateway Introduction Security Content FilteringAutosensing 10/100 Ethernet TCP/IP Easy Installation and ManagementMaintenance and Support Introduction Package Contents Chapter Setting Up the HardwarePC Requirements Access RequirementLocal Network Hardware Requirements Gateway’s Front PanelLED Descriptions Gateway’s Rear PanelConnecting the Gateway Typical installation Connecting to your Local Ethernet NetworkAdsl through a modular RJ-11 wall jack Connecting to Your Adsl Service and Telephone ProviderVerifying Power Connecting the Power AdapterAdsl through other wall jacks Setting Up the Hardware Preparing Your Personal Computers for IP Networking Chapter Preparing Your NetworkInstall or Verify Windows Networking Components Configuring Windows 95, 98, and ME for IP NetworkingPreparing Your Network Selecting Internet Access Method Assign TCP/IP configuration by DhcpVerifying TCP/IP Properties Windows Configuring Windows NT or 2000 for IP NetworkingVerifying TCP/IP Properties Configuring the Macintosh for IP NetworkingMacOS 8.6 or MacOS Verifying TCP/IP Properties Macintosh Your Internet AccountAccount Information Login ProtocolsObtaining ISP Configuration Information Windows Obtaining ISP Configuration Information Macintosh Ready for ConfigurationRestarting the Network Preparing Your Network Accessing the Web Configuration Manager Chapter Basic Configuration of the GatewayLogin window opens as shown in -1below Browser-based configuration main menu Configuration using the Setup Wizard Setup Wizard menu for Dynamic IP address Configuring for Dynamic IP AccountSetup Wizard menu for Fixed IP address Configuring for Fixed IP AccountSetup Wizard menu for PPPoE login accounts Configuring for an Account with LoginManual Configuration Completing the Configuration Basic Configuration of the Gateway Configuring for Content Filtering Chapter Content FilteringLogs Block Sites Schedule Mail Content Filtering Gateway Status Chapter MaintenanceThis screen shows the following parameters Dhcp This screen shows the following statistics PPPoE Status screen Ping Status screen Attached DevicesRestore and Backup the Configuration Configuration File Settings ManagementErase the Configuration Changing the Configuration PasswordGateway Upgrade menu Gateway UpgradeMaintenance Configuring for Port Forwarding to Local Servers Advanced Configuration of the GatewayAdd a Custom Service Local Web and FTP Server Example Edit or Delete a Port Forwarding EntryTip Multiple Computers for Half Life, Kali or Quake NAT Status DMZ Server SecurityRespond to Ping on Internet WAN Port Dynamic DNSLAN IP Setup Menu LAN IP SetupUse router as Dhcp server LAN TCP/IP SetupStatic Routes Static Route Summary Table Static Route Example Advanced Configuration of the Gateway Basic Functioning Chapter TroubleshootingPWR LED Not On Test LED Never Blinks or LED Stays On Troubleshooting the Web Configuration InterfaceWAN LED Blinking Yellow Troubleshooting the ISP ConnectionAdsl link WAN LED Green or Blinking GreenWAN LED Off Obtaining a WAN IP AddressTroubleshooting Internet Browsing Troubleshooting PPPoE or PPPoATesting the LAN Path to Your Gateway Troubleshooting a TCP/IP Network Using a Ping UtilityPing -n 10 IP address Testing the Path from Your PC to a Remote DeviceProblems with Date and Time Restoring the Default Configuration and PasswordUsing the Default Reset button General Specifications Appendix a Technical SpecificationsLAN Appendix B Networks and Routing Basics What is a Router?Basic Router Concepts IP Addresses and the Internet Routing Information ProtocolClass E Class E addresses are for experimental use Subnet Addressing NetmaskFigure B-2. Example of Subnetting a Class B Address Table B-1. Netmask Notation Translation Table for One Octet Private IP Addresses Single IP Address Operation Using NATFigure B-3. Single IP Address Operation Using NAT Domain Name Server MAC Addresses and Address Resolution ProtocolIP Configuration by Dhcp Ethernet Cabling Uplink Switches, Crossover Cables, and MDI/MDIX SwitchingCable Quality Glossary For example Internet Through the network Auto MDI/MDI-X1-4, 2-6, B-11, B-12 DMZ 1-3, 5-2 MDI/MDI-X1-4, 2-6, B-11, B-12 NTP 5-6 Xiii, B-7 1631 xiv, B-8