Bryston SP1.7 manual Status LED, Photo Sensor

Page 19

Pressing the OSD (On-Screen Display) Button will toggle the OSD function on and off, on your video monitor, if you are using the Bryston SPV-1 video switcher.

Pressing the SUB button will engage the menu for the volume trim level of the subwoofer channel. Use the MENU/UP/DOWN button to change the subwoofer channel level up or down. Press SELECT when finished.

Pressing the CENTER button will engage the menu for the volume trim level of the center channel. Use the MENU/UP/DOWN button to change the center channel level up or down. Press SELECT when finished.

Pressing the REAR button will engage the menu for the volume trim level of the rear channels. Use the MENU/UP/DOWN button to change the rear channel levels up or down. Press SELECT when finished.

Pressing the BACK button will engage the menu for the volume trim level of the back channel(s). Use the MENU/UP/DOWN button to change the back channel level(s) up or down. Press SELECT when finished.

12. Status LED

Indicates remote control status while accessing discrete/hidden functions, and changing remote options. Contact the factory for details.

13. Photo Sensor

Works in conjunction with the backlight and tilt switch to determine if backlighting is needed.

NOTE: To enable or disable the backlight in the remote control, follow this procedure:

i.Press CODE button for 5 seconds

ii.LED will flash red, then release button

iii.Type in 3 digit code 792 = MODE / SAVE / DTS

iv.LED will flash again to confirm

To send discrete/hidden Code…

i.Press CODE button and release

ii.LED will illuminate (Red)

iii.Type in 3 digit code (a combination of mode buttons)

iv.LED will flash again to confirm and go out.

For a list of hidden codes, visit the Bryston Website at www.bryston.ca

17

Image 19

Contents SP1.7 800 632 Bryston 20-YEARWARRANTYContents SP1.7 Functional Layout AccessoriesPower Input Mode PowerPower Momentary Switch Front Panel Controls and IndicatorsStandby and IR Infrared Activity Indicator LCD Display window Using the Dynamic Range ControlMenu Control Buttons Source Selection Buttons and IndicatorsDigital Mode and Indicator Mode Selection ButtonsSurround Button Mono and Mono Downmix Modes Stereo and Stereo Downmix ModeTHX Button Available with THX Listening Mode… Mode ButtonBypass Button Master VolumeAnalog Balance Digital Audio Coaxial Inputs Rear Panel Input and Output ConnectionsBalanced and 2. Unbalanced Outputs Analog InputsToslink Digital Audio Optical Inputs Setting the Optical Audio Input AssignmentTape/Recording Outputs Aux IR Receiver RS-232 connectorRemote 12V Trigger Outputs Programming the AUX Trigger OutputSource Select Buttons SP1.7 Remote ControlIEC Power Connector Fuses Master Power SwitchSetup Buttons Mode Select ButtonsVolume/Trim Buttons Power ButtonPhoto Sensor Status LEDTo accomplish this process the following tools are needed SET UP and Calibration of the SP1.7Setting the Speaker Configuration Explanation of ‘Saved Settings per Source’ FeatureExplanation of ‘Xtra Bass’ Mode Highlight SP Setup Menu Setting the Speaker Crossover FrequencyChange the Crossover Frequency Setting the Channel DelaysSetting Channel Levels without Pink Noise Calibrating and Setting Levels/Channel to Channel BalanceSetting the THX Subwoofer Limiter or Bass Peak Level Manager Setting the Bplm with Pink NoiseEnabling DTS-ES 6.1 Decoding Setting the Bplm without Pink NoiseEnabling THX Surround EX Decoding Hightlight ES Other Settings MenuChange EX Control Setting Changing Dolby Plii Music SettingsHighlight Plii Setup Menu Center Image is a variable in Neo6 music mode only Changing DTS NEO6 SettingsAcknowledgements To change the Center ImageSurround Modes Appendix a SP1.7 Surround ModesPage Table of all available surround modes SignalDTS as per THX licensing agreements Appendix B THX InformationXLR/PHONE Example HOOK-UP DiagramsInputs SP1.7 SpecificationsSuggested Surround Speaker Placement