Bryston SP1.7 manual Mode Selection Buttons, Digital Mode and Indicator, Surround Button

Page 9

MODE SELECTION BUTTONS:

8. Digital Mode and Indicator

This button operates as a three-way toggle function. The LED immediately above the button has two colors - RED and GREEN, and an OFF mode where it is not illuminated.

When Digital Mode is selected, the decoder will automatically default to a digital signal for the selected input if one is present.

If a digital signal is present and detected, the SP1.7 will automatically determine the type of bitstream and select the proper decoding mode. The indicator LED will turn green when this happens.

If NO DIGITAL SIGNAL is detected the SP1.7 will default back to the analog input for the selected source. This also automatically puts the SP1.7 into its Digital Standby Mode. When this occurs the LED indicator will turn RED

In this mode, the decoder will continually check the selected source inputs for the presence of a digital signal. If one is detected, the SP1.7 will auto- matically switch over to the pre-selected digital operation mode for that source.

To defeat this auto-digital detect mode you must press the button again. If you do the LED will go OFF.

When this mode of operation is selected the SP1.7 will look at ONLY its analog inputs. If a digital signal does appear the SP1.7 will NOT recognize it and will remain in its analog only mode until you press the Digital button again to either select the digital source or place the SP1.7 into its auto detect mode as explained above.

DIGITAL

9. Surround Button

Pressing this button will engage the SP1.7’s surround listening mode. When this function is operational the LED will turn green. For Dolby Digital 5.1, DTS 5.1, and DTS-ES 6.1 bitstreams, the signal will be decoded and pre- sented with no additional post-processing. For 2-channel source material, the SP1 will synthesize surround information based on the chosen Surround Mode (see 31. for Surround Mode information).

SURROUND

7

Page 8 Page 10
Image 9
Page 8 Page 10
Contents SP1.7 800 632 Bryston 20-YEARWARRANTYContents SP1.7 Functional Layout AccessoriesPower Input Mode PowerFront Panel Controls and Indicators Power Momentary SwitchStandby and IR Infrared Activity Indicator LCD Display window Using the Dynamic Range ControlMenu Control Buttons Source Selection Buttons and IndicatorsMode Selection Buttons Digital Mode and IndicatorSurround Button Mono and Mono Downmix Modes Stereo and Stereo Downmix ModeTHX Button Available with THX Listening Mode… Mode ButtonMaster Volume Bypass ButtonAnalog Balance Balanced and 2. Unbalanced Outputs Rear Panel Input and Output ConnectionsAnalog Inputs Digital Audio Coaxial InputsSetting the Optical Audio Input Assignment Toslink Digital Audio Optical InputsTape/Recording Outputs Remote 12V Trigger Outputs RS-232 connectorProgramming the AUX Trigger Output Aux IR ReceiverIEC Power Connector Fuses SP1.7 Remote ControlMaster Power Switch Source Select ButtonsVolume/Trim Buttons Mode Select ButtonsPower Button Setup ButtonsPhoto Sensor Status LEDTo accomplish this process the following tools are needed SET UP and Calibration of the SP1.7Setting the Speaker Configuration Explanation of ‘Saved Settings per Source’ FeatureExplanation of ‘Xtra Bass’ Mode Highlight SP Setup Menu Setting the Speaker Crossover FrequencyChange the Crossover Frequency Setting the Channel DelaysSetting Channel Levels without Pink Noise Calibrating and Setting Levels/Channel to Channel BalanceSetting the THX Subwoofer Limiter or Bass Peak Level Manager Setting the Bplm with Pink NoiseEnabling DTS-ES 6.1 Decoding Setting the Bplm without Pink NoiseEnabling THX Surround EX Decoding Hightlight ES Other Settings MenuChange EX Control Setting Changing Dolby Plii Music SettingsHighlight Plii Setup Menu Center Image is a variable in Neo6 music mode only Changing DTS NEO6 SettingsAcknowledgements To change the Center ImageSurround Modes Appendix a SP1.7 Surround ModesPage Table of all available surround modes SignalDTS as per THX licensing agreements Appendix B THX InformationXLR/PHONE Example HOOK-UP DiagramsInputs SP1.7 SpecificationsSuggested Surround Speaker Placement
Top Page Image Contents