Bryston SP1.7 manual Calibrating and Setting Levels/Channel to Channel Balance

Page 25

3.Move the cursor to the speaker you want to set the distance/delay for (L C R RS LS RB LB SB). Hit Select. Now you can adjust the Delay value which is equivalent to the distance you measured for the selected speaker using the arrow buttons. Set the delay for each speaker in your system to the nearest foot/meter. Rounding up is OK. Remember that if one back speaker is selected, the Left Back output is used to set the delay.

4.Hit SELECT or [X] Exit when finished.

The SP1.7’s default factory settings as shipped are 10 feet to every speaker, resulting in zero overall delay.

Calibrating and Setting Levels/Channel to Channel Balance.

1.Position the Sound Level Meter at the Centre point of your listening area, at average ear height [approximately 40 - 46 inches {102 - 117 cm.} with its microphone positioned vertically (pointing at the ceiling). DO NOT aim the sensing microphone at the speakers, as this will produce inaccurate level indications.

2.Using the SP1.7 Remote, press and hold for approximately 3-5 seconds the key labeled “TEST”.

IMPORTANT: The Test-Noise Mode can only be initiated from the SP1.7 remote, and not from the front panel.

The shaped pink-noise test signal will begin with the left-front loudspeaker. If the signal does not appear in this speaker please stop the process and check your wiring and connections for proper configuration.

IMPORTANT: When using the Pink Noise generator within the SP1.7 for speaker level calibration, the salient point is that all channels measure equal dB. After pushing the test button, the pink noise will start in the front left speaker. Record the dB level from this speaker (with the level trim value at 0 dB on the LCD Display), and adjust all the others to match it. It is not critical to reach some specific dB level (ex. 85 dB), it is more important that all channels are at equal levels.

3.Hit the “TEST” button again to sequence the noise to the next speaker. The sequence is L -> C -> R -> RS -> RB -> LB -> LS -> SUB -> EXIT.

4.Using the volume up/down arrows on the remote or the arrow keys on the SP1.7 adjust the level of the noise for each speaker so that it matches the front left channel noise (dB) level on the Sound Level Meter.

5.When the cycle is complete, the test noise signal will end, and the unit will switch back to the previous mode. If any output is unused (as defined by ‘NONE’ in the Speaker Configuration Setup), the noise sequence will automatically skip to the next speaker in the sequence.

Setting Channel Levels without Pink Noise

If you wish to adjust the speaker level trims without using the pink-noise test signal, this can be done from the Front Panel menu system.

23

Image 25
Contents SP1.7 800 632 Bryston 20-YEARWARRANTYContents SP1.7 Functional Layout AccessoriesPower Input Mode PowerPower Momentary Switch Front Panel Controls and IndicatorsStandby and IR Infrared Activity Indicator LCD Display window Using the Dynamic Range ControlMenu Control Buttons Source Selection Buttons and IndicatorsDigital Mode and Indicator Mode Selection ButtonsSurround Button Mono and Mono Downmix Modes Stereo and Stereo Downmix ModeTHX Button Available with THX Listening Mode… Mode ButtonBypass Button Master VolumeAnalog Balance Balanced and 2. Unbalanced Outputs Rear Panel Input and Output ConnectionsAnalog Inputs Digital Audio Coaxial InputsToslink Digital Audio Optical Inputs Setting the Optical Audio Input AssignmentTape/Recording Outputs Remote 12V Trigger Outputs RS-232 connectorProgramming the AUX Trigger Output Aux IR ReceiverIEC Power Connector Fuses SP1.7 Remote ControlMaster Power Switch Source Select ButtonsVolume/Trim Buttons Mode Select ButtonsPower Button Setup ButtonsPhoto Sensor Status LEDTo accomplish this process the following tools are needed SET UP and Calibration of the SP1.7Setting the Speaker Configuration Explanation of ‘Saved Settings per Source’ FeatureExplanation of ‘Xtra Bass’ Mode Highlight SP Setup Menu Setting the Speaker Crossover FrequencyChange the Crossover Frequency Setting the Channel DelaysSetting Channel Levels without Pink Noise Calibrating and Setting Levels/Channel to Channel BalanceSetting the THX Subwoofer Limiter or Bass Peak Level Manager Setting the Bplm with Pink NoiseEnabling DTS-ES 6.1 Decoding Setting the Bplm without Pink NoiseEnabling THX Surround EX Decoding Hightlight ES Other Settings MenuChange EX Control Setting Changing Dolby Plii Music SettingsHighlight Plii Setup Menu Center Image is a variable in Neo6 music mode only Changing DTS NEO6 SettingsAcknowledgements To change the Center ImageSurround Modes Appendix a SP1.7 Surround ModesPage Table of all available surround modes SignalDTS as per THX licensing agreements Appendix B THX InformationXLR/PHONE Example HOOK-UP DiagramsInputs SP1.7 SpecificationsSuggested Surround Speaker Placement