Bryston manual SP1.7 Specifications, Inputs

Page 38

SP1.7 SPECIFICATIONS

Inputs
Analog Audio:	Six stereo (RCA) pairs, One 5.1 channel (RCA) input
Digital:	4 coaxial (RCA) 75 Ohms, 2 Optical (TOSLINK?), conforms to S/PDIF standard.
	Pro version 1 AES/EBU input (XLR) 110 Ohms
Infrared:	1 mini phone jack
RS-232:	D9 connector (bidirectional)
Outputs
Analog Outputs:	Left, Centre, Right, Right Surround, Left Surround, and Subwoofer on 6 unbalanced
	(RCA) and 6 balanced (XLR).
	2 stereo (RCA) pairs of Record Outputs.
	1 pair (RCA) Surround Back outputs
Trigger:	One 12V on/off trigger, One 12V programmable trigger, to source 80mA total.

Remote

30 button, Hand-Held, Infrared remote control unit operates with two AAA batteries (included).

Performance Specifications
A/D Conversion:	24-Bit, 48kHz Delta-Sigma
D/A Conversion:	24-Bit, 96kHz Delta-Sigma
DSP Engine:	Motorola 56367
Power Supply:	Dual, Linear, Toroidal
Frequency Response:	20Hz to 20kHz +/- 0.25 dB
THD+Noise:	Less than 0.006% in DSP modes; Less than 0.0025% in Bypass mode 20Hz to
	20kHz at maximum output level.
Signal-to-Noise Ratio:	105dB in DSP Modes; 110dB in 2ch Bypass Mode ; 22kHz bandwidth, Ref. 1kHz at
	maximum output level
Input Level:	2 Vrms in DSP modes; 4 Vrms in Bypass Mode
Input Impedance:	50kOhms
Output Level:	8 Vrms (16 Vrms Balanced) in DSP Modes; 10 Vrms (20 Vrms Balanced) in Bypass Mode.
Output Impedance:	110 Ohms
Bass Management:	2nd Order HPF(x5), 4th Order LPF; 60 – 220 Hz Crossover Freq.
Physical Specifications
Power Requirements	100VAC, 115VAC, and 230VAC models. 200 VA. IEC detachable power cord (included)
Dimensions:	17” W x 13.5” D x 3.8” H; rackmount 19” W x 13.5” D x 3.5” H
Weight:	approx 22 lbs (10 kg)
Chassis Temp:	0 to 50 deg Celsius

Specifications subject to change without notice.

36

Image 38

Contents SP1.7 Bryston 20-YEARWARRANTY 800 632Contents Accessories SP1.7 Functional LayoutPower Power Input ModeStandby and IR Infrared Activity Indicator Front Panel Controls and IndicatorsPower Momentary Switch Using the Dynamic Range Control LCD Display windowSource Selection Buttons and Indicators Menu Control ButtonsSurround Button Mode Selection ButtonsDigital Mode and Indicator Stereo and Stereo Downmix Mode Mono and Mono Downmix ModesTHX Button Mode Button Available with THX Listening Mode…Analog Balance Master VolumeBypass Button Analog Inputs Rear Panel Input and Output ConnectionsBalanced and 2. Unbalanced Outputs Digital Audio Coaxial InputsTape/Recording Outputs Setting the Optical Audio Input AssignmentToslink Digital Audio Optical Inputs Programming the AUX Trigger Output RS-232 connectorRemote 12V Trigger Outputs Aux IR ReceiverMaster Power Switch SP1.7 Remote ControlIEC Power Connector Fuses Source Select ButtonsPower Button Mode Select ButtonsVolume/Trim Buttons Setup ButtonsStatus LED Photo SensorSET UP and Calibration of the SP1.7 To accomplish this process the following tools are neededExplanation of ‘Saved Settings per Source’ Feature Setting the Speaker ConfigurationExplanation of ‘Xtra Bass’ Mode Setting the Speaker Crossover Frequency Highlight SP Setup MenuSetting the Channel Delays Change the Crossover FrequencyCalibrating and Setting Levels/Channel to Channel Balance Setting Channel Levels without Pink NoiseSetting the Bplm with Pink Noise Setting the THX Subwoofer Limiter or Bass Peak Level ManagerSetting the Bplm without Pink Noise Enabling DTS-ES 6.1 DecodingHightlight ES Other Settings Menu Enabling THX Surround EX DecodingChanging Dolby Plii Music Settings Change EX Control SettingHighlight Plii Setup Menu Changing DTS NEO6 Settings Center Image is a variable in Neo6 music mode onlyTo change the Center Image AcknowledgementsAppendix a SP1.7 Surround Modes Surround ModesPage Signal Table of all available surround modesAppendix B THX Information DTS as per THX licensing agreementsExample HOOK-UP Diagrams XLR/PHONESP1.7 Specifications InputsSuggested Surround Speaker Placement