Lantronix UDS2100 manual Getting Started, Package Contents

Page 13

3: Getting Started

This chapter describes how to get your UDS up and running in the shortest possible time.

Package Contents

Verify and inspect the contents of the UDS2100 package using the following list. If any item is missing or damaged, contact your place of purchase immediately.

UDS2100

DB9F to DB9F Null Modem Cable (P/N 500-164)

Power supply

CD with UDS2100 User Guide and utilities (DeviceInstaller and Com Port

Redirector)

Quick Start Guide

UDS2100 User Guide

Image 13

Contents UDS2100 User Guide Contacts Copyright & TrademarkRevisions Date Rev CommentsContents Setup Mode Server Configuration Warranty Tables FiguresPurpose and Audience Using This GuideChapter Summary Chapter DescriptionDocument Additional DocumentationApplications IntroductionApplication Examples Introduction Configuration Methods Additional FeaturesProtocol Support Sample Hardware Address 00-20-4A-14-01-18 or 00204A140118 Product Information LabelGetting Started Package ContentsTo install the unit Installing the UDSHardware Address Required InformationIP Address IP Address Subnet Mask GatewayInstalling DeviceInstaller Assigning the IP Address DeviceInstallerAssigning an IP Address Select Assign a specific IP address and click NextViewing the Current Configuration Accessing the UDS2100 Using DeviceInstallerTo view the units current settings Adding the Unit to the Manage ListGetting Started SettingNext Step To configure the unit using a Telnet sessionPress Enter within 5 seconds Assigning the IP Address Serial Port Login Accessing UDS2100 Using DeviceInstaller Configuration Using Web ManagerLantronix Web Manager Network ConfigurationTo assign an IP address automatically Automatic IP Address ConfigurationSelect Obtain IP address automatically Ethernet Configuration Static IP Address ConfigurationSelect Use the following IP configuration To assign an IP address manuallyTo configure the UDS2100’s device server settings Server ConfigurationServer Configuration AdvancedTo configure the host list Host List ConfigurationSerial Settings Channel 1 and Channel 2 ConfigurationRetry Settings Host InformationChannel Port SettingsFlush Input Buffer Serial to Network Pack ControlTo configure a channel’s TCP settings Connection Settings TCPFlush Output Buffer Network to Serial Connect Mode Active Connection Connect Mode Passive ConnectionEndpoint Configuration Connect ProtocolCommon Options Disconnect ModeTo configure a channel’s UDP settings Connection Settings UDPDatagram Mode Apply Factory Defaults Apply SettingsAccessing Setup Mode Configuration via Telnet or Serial Port Setup ModeTelnet Connection To establish a Telnet connection Serial Port ConnectionTo exit setup mode Exiting Setup ModeServer Configuration Option Setup Mode Server ConfigurationIP Address Set Gateway IP AddressNetmask Number of Bits for Host Part Change Telnet Configuration PasswordDhcp Name Network Class Host Bits NetmaskSetup Mode Server Configuration Channel 1 Option Setup Mode Channel ConfigurationBaudrate Mode Option Interface ModeCommon I/F Mode Setting Binary FlowPort Number Connect ModeFlow Control Option Hex Port Numbers Reserved forConnect Mode Option Response Incoming ConnectionActive Startup Manual Connection Address Example Datagram Type To enable the hostlistModem Mode No Carrier MessageMeaningModem Mode Function Command Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Remote IP Address Disconnect Mode OptionRemote Port DisConnModePack Control Flush Mode Buffer FlushingTrailing Characters Packing IntervalSend Characters OptionChannel Port Password DisConnTime Inactivity TimeoutSend Characters Telnet Terminal TypeExpert Settings Option Setup Mode Advanced SettingsTCP Keepalive time in seconds Disable Monitor Mode at bootup ARP Cache timeout in secondsEnable alternate MAC Http Port NumberDisable Snmp Security Settings OptionDisable Telnet Setup Snmp Community NameDisable Port 77FE Hex Disable Tftp Firmware UpdateDisable Web Server Disable Web SetupChannel 1 and Channel 2 Configuration Defaults Default Settings OptionExpert Settings Defaults Security Settings DefaultsSetup Mode Advanced Settings Using Tftp Graphical User Interface Firmware UpgradesObtaining Firmware Reloading Firmware ROM FileTo recover firmware Using Tftp Command Line InterfaceFirmware Upgrades Entering Monitor Mode Using the Serial Port Monitor ModeEntering Monitor Mode Using the Network Port Monitor Mode CommandsResponse Meaning Command Command Name FunctionLEDs Troubleshooting and Contact InformationLEDs Meaning Diagnostic, Power, and Serial Port LEDs UDS2100 LEDsProblem/Message Reason Solution Problems and Error MessagesProblem/Message Reason Solution Technical Support Europe, Middle East, and Africa Technical SupportConnections and Pinouts Serial Connector PinoutsUDS2100 Serial Ports Ethernet Connector Pinouts Power Plug Reset ButtonTo reset the unit to factory defaults Network PortCategory Description Technical SpecificationsCategory Description Transient over voltages AutoIP Alternative Ways to Assign an IP AddressTo assign a temporary IP address ARP and TelnetConversion Table Converting Binary to HexadecimalDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index