Lantronix UDS2100 manual Firmware Upgrades

Page 63

9: Firmware Upgrades

5.For Device Model, be sure the appropriate device (e.g., UDS2100) displays.

6.For Firmware File, click the Browse button and go to the location where the firmware file resides.

Note: Make sure the UDS2100 on which you are recovering firmware is connected to this selected port on your PC.

7.Click OK to download the file.

8.When prompted, reset the device. Status messages and a progress bar at the bottom of the screen show the progress of the file transfer. When the file transfer completes, the message “Successful, Click OK to Close” displays.

9.Click the OK button to complete this procedure.

Note For more information, see Recovering Firmware in the DeviceInstaller online Help.

UDS2100 User Guide

Image 63

Contents UDS2100 User Guide Date Rev Comments Copyright & TrademarkContacts RevisionsContents Setup Mode Server Configuration Warranty Tables FiguresChapter Description Using This GuidePurpose and Audience Chapter SummaryDocument Additional DocumentationIntroduction ApplicationsApplication Examples Introduction Additional Features Configuration MethodsProtocol Support Sample Hardware Address 00-20-4A-14-01-18 or 00204A140118 Product Information LabelGetting Started Package ContentsTo install the unit Installing the UDSIP Address Subnet Mask Gateway Required InformationHardware Address IP AddressSelect Assign a specific IP address and click Next Assigning the IP Address DeviceInstallerInstalling DeviceInstaller Assigning an IP AddressAdding the Unit to the Manage List Accessing the UDS2100 Using DeviceInstallerViewing the Current Configuration To view the units current settingsGetting Started SettingTo configure the unit using a Telnet session Next StepPress Enter within 5 seconds Assigning the IP Address Serial Port Login Accessing UDS2100 Using DeviceInstaller Configuration Using Web ManagerLantronix Web Manager Network ConfigurationAutomatic IP Address Configuration To assign an IP address automaticallySelect Obtain IP address automatically To assign an IP address manually Static IP Address ConfigurationEthernet Configuration Select Use the following IP configurationAdvanced Server ConfigurationTo configure the UDS2100’s device server settings Server ConfigurationTo configure the host list Host List ConfigurationHost Information Channel 1 and Channel 2 ConfigurationSerial Settings Retry SettingsChannel Port SettingsFlush Input Buffer Serial to Network Pack ControlConnection Settings TCP To configure a channel’s TCP settingsFlush Output Buffer Network to Serial Connect Protocol Connect Mode Passive ConnectionConnect Mode Active Connection Endpoint ConfigurationCommon Options Disconnect ModeConnection Settings UDP To configure a channel’s UDP settingsDatagram Mode Apply Factory Defaults Apply SettingsConfiguration via Telnet or Serial Port Setup Mode Accessing Setup ModeTelnet Connection To establish a Telnet connection Serial Port ConnectionTo exit setup mode Exiting Setup ModeSet Gateway IP Address Setup Mode Server ConfigurationServer Configuration Option IP AddressNetwork Class Host Bits Netmask Change Telnet Configuration PasswordNetmask Number of Bits for Host Part Dhcp NameSetup Mode Server Configuration Setup Mode Channel Configuration Channel 1 OptionBaudrate Flow Interface ModeMode Option Common I/F Mode Setting BinaryPort Numbers Reserved for Connect ModePort Number Flow Control Option HexConnect Mode Option Incoming Connection ResponseActive Startup Manual Connection Address Example Datagram Type To enable the hostlistModem Mode No Carrier MessageMeaningSend the Escape Sequence +++ in Modem Mode Modem Mode Function CommandAuto Increment Source Port DisConnMode Disconnect Mode OptionRemote IP Address Remote PortPack Control Flush Mode Buffer FlushingOption Packing IntervalTrailing Characters Send CharactersTelnet Terminal Type DisConnTime Inactivity TimeoutChannel Port Password Send CharactersSetup Mode Advanced Settings Expert Settings OptionTCP Keepalive time in seconds Http Port Number ARP Cache timeout in secondsDisable Monitor Mode at bootup Enable alternate MACSnmp Community Name Security Settings OptionDisable Snmp Disable Telnet SetupDisable Web Setup Disable Tftp Firmware UpdateDisable Port 77FE Hex Disable Web ServerSecurity Settings Defaults Default Settings OptionChannel 1 and Channel 2 Configuration Defaults Expert Settings Defaults Setup Mode Advanced Settings ROM File Firmware UpgradesUsing Tftp Graphical User Interface Obtaining Firmware Reloading FirmwareTo recover firmware Using Tftp Command Line InterfaceFirmware Upgrades Monitor Mode Commands Monitor ModeEntering Monitor Mode Using the Serial Port Entering Monitor Mode Using the Network PortResponse Meaning Command Command Name FunctionLEDs Troubleshooting and Contact InformationLEDs Meaning Diagnostic, Power, and Serial Port LEDs UDS2100 LEDsProblem/Message Reason Solution Problems and Error MessagesProblem/Message Reason Solution Technical Support Europe, Middle East, and Africa Technical SupportSerial Connector Pinouts Connections and PinoutsUDS2100 Serial Ports Network Port Reset ButtonEthernet Connector Pinouts Power Plug To reset the unit to factory defaultsCategory Description Technical SpecificationsCategory Description Transient over voltages AutoIP Alternative Ways to Assign an IP AddressTo assign a temporary IP address ARP and TelnetConverting Binary to Hexadecimal Conversion TableDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index