Lantronix UDS2100 manual Copyright & Trademark, Contacts, Revisions, Date Rev Comments

Page 2

Copyright & Trademark

© 2006, Lantronix. All rights reserved. No part of the contents of this book may be transmitted or reproduced in any form or by any means without the written permission of Lantronix. Printed in the United States of America.

Ethernet is a trademark of XEROX Corporation. UNIX is a registered trademark of The Open Group. Windows 95, Windows 98, Windows 2000, and Windows NT are trademarks of Microsoft Corp. Netscape is a trademark of Netscape Communications Corporation.

Contacts

Lantronix

15353 Barranca Parkway

Irvine, CA 92618, USA

Phone: 949-453-3990

Fax: 949-453-3995

Technical Support

Online: www.lantronix.com/support

Sales Offices

For a current list of our domestic and international sales offices, go to the Lantronix Web site at http://www.lantronix.com/about/contact/index.html

Revisions

	Date	Rev.	Comments
	9/06	A	Initial document

UDS2100 User Guide

Image 2

Contents UDS2100 User Guide Revisions Copyright & TrademarkContacts Date Rev CommentsContents Setup Mode Server Configuration Warranty Figures TablesChapter Summary Using This GuidePurpose and Audience Chapter DescriptionAdditional Documentation DocumentApplication Examples IntroductionApplications Introduction Protocol Support Additional FeaturesConfiguration Methods Product Information Label Sample Hardware Address 00-20-4A-14-01-18 or 00204A140118Package Contents Getting StartedInstalling the UDS To install the unitIP Address Required InformationHardware Address IP Address Subnet Mask GatewayAssigning an IP Address Assigning the IP Address DeviceInstallerInstalling DeviceInstaller Select Assign a specific IP address and click NextTo view the units current settings Accessing the UDS2100 Using DeviceInstallerViewing the Current Configuration Adding the Unit to the Manage ListSetting Getting StartedPress Enter within 5 seconds To configure the unit using a Telnet sessionNext Step Assigning the IP Address Serial Port Login Configuration Using Web Manager Accessing UDS2100 Using DeviceInstallerNetwork Configuration Lantronix Web ManagerSelect Obtain IP address automatically Automatic IP Address ConfigurationTo assign an IP address automatically Select Use the following IP configuration Static IP Address ConfigurationEthernet Configuration To assign an IP address manuallyServer Configuration Server ConfigurationTo configure the UDS2100’s device server settings AdvancedHost List Configuration To configure the host listRetry Settings Channel 1 and Channel 2 ConfigurationSerial Settings Host InformationPort Settings ChannelPack Control Flush Input Buffer Serial to NetworkFlush Output Buffer Network to Serial Connection Settings TCPTo configure a channel’s TCP settings Endpoint Configuration Connect Mode Passive ConnectionConnect Mode Active Connection Connect ProtocolDisconnect Mode Common OptionsDatagram Mode Connection Settings UDPTo configure a channel’s UDP settings Apply Settings Apply Factory DefaultsTelnet Connection Configuration via Telnet or Serial Port Setup ModeAccessing Setup Mode Serial Port Connection To establish a Telnet connectionExiting Setup Mode To exit setup modeIP Address Setup Mode Server ConfigurationServer Configuration Option Set Gateway IP AddressDhcp Name Change Telnet Configuration PasswordNetmask Number of Bits for Host Part Network Class Host Bits NetmaskSetup Mode Server Configuration Baudrate Setup Mode Channel ConfigurationChannel 1 Option Common I/F Mode Setting Binary Interface ModeMode Option FlowFlow Control Option Hex Connect ModePort Number Port Numbers Reserved forConnect Mode Option Active Startup Incoming ConnectionResponse Manual Connection Address Example To enable the hostlist Datagram TypeModem Mode MessageMeaning No CarrierAuto Increment Source Port Send the Escape Sequence +++ in Modem ModeModem Mode Function Command Remote Port Disconnect Mode OptionRemote IP Address DisConnModeFlush Mode Buffer Flushing Pack ControlSend Characters Packing IntervalTrailing Characters OptionSend Characters DisConnTime Inactivity TimeoutChannel Port Password Telnet Terminal TypeTCP Keepalive time in seconds Setup Mode Advanced SettingsExpert Settings Option Enable alternate MAC ARP Cache timeout in secondsDisable Monitor Mode at bootup Http Port NumberDisable Telnet Setup Security Settings OptionDisable Snmp Snmp Community NameDisable Web Server Disable Tftp Firmware UpdateDisable Port 77FE Hex Disable Web SetupExpert Settings Defaults Default Settings OptionChannel 1 and Channel 2 Configuration Defaults Security Settings DefaultsSetup Mode Advanced Settings Obtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface ROM FileUsing Tftp Command Line Interface To recover firmwareFirmware Upgrades Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port Monitor Mode CommandsCommand Command Name Function Response MeaningTroubleshooting and Contact Information LEDsDiagnostic, Power, and Serial Port LEDs UDS2100 LEDs LEDs MeaningProblems and Error Messages Problem/Message Reason SolutionProblem/Message Reason Solution Technical Support Technical Support Europe, Middle East, and AfricaUDS2100 Serial Ports Serial Connector PinoutsConnections and Pinouts To reset the unit to factory defaults Reset ButtonEthernet Connector Pinouts Power Plug Network PortTechnical Specifications Category DescriptionCategory Description Transient over voltages Alternative Ways to Assign an IP Address AutoIPARP and Telnet To assign a temporary IP addressDecimal Binary Hex Converting Binary to HexadecimalConversion Table Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index

Copyright & Trademark

Contacts

Revisions

Date

Rev.

Comments