Lantronix UDS2100 manual Manual Connection Address Example

Page 46

7: Setup Mode: Channel Configuration

 

 

 

 

 

If a partial IP address is presented in a command string, it is

 

 

 

 

 

interpreted to be the least significant bytes of the IP address

 

 

 

 

 

and uses the internally stored remote IP address to provide

 

 

 

 

 

the most significant bytes of the IP address. If the IP

 

 

 

 

 

address entered is 0.0.0.0/0, the device server enters

 

 

 

 

 

Monitor Mode.

 

 

 

 

 

For example, if the remote IP address already configured in

 

 

 

 

 

the unit is 129.1.2.3, then an example command string

 

 

 

 

 

would be C3/7. (This would connect to 129.1.2.3 and port 7.)

 

 

 

 

 

You may also use a different ending for the connection

 

 

 

 

 

string. For example, C50.1/23 would connect you to

 

 

 

 

 

129.1.50.1 and port 23.

 

 

 

 

 

 

 

 

 

Figure 7-3. Manual Connection Address Example

 

 

Command String

 

Result if remote IP is 129.1.2.3 and remote port is 1234

 

 

 

 

 

 

 

 

 

 

C121.2.4.5/1

 

Complete override; connection is started with host 121.2.4.5,

 

 

 

port 1.

 

 

 

 

 

 

 

 

 

 

 

 

C5

 

Connects to 129.1.2.5, port 1234.

 

 

 

 

 

 

 

C28.10/12

Connects to 129.1.28.10, port 12.

 

 

 

 

 

 

 

 

C0.0.0.0/0

 

Enters Monitor Mode.

 

 

 

 

 

 

 

 

Autostart (Automatic

 

 

If you enable Autostart, the unit automatically connects to

Connection)

 

 

the remote IP address and remote port specified when the

 

 

 

 

 

firmware starts.

 

 

 

 

Hostlist

 

 

If you enable this option, the device server scrolls through

 

 

 

 

 

the hostlist until it connects to a device listed in the hostlist

 

 

 

 

 

table. Once it connects, the unit stops trying to connect to

 

 

 

 

 

any others. If this connection fails, the unit continues to

 

 

 

 

 

scroll through the table until it is able to connect to another

 

 

 

 

 

IP in the hostlist. Hostlist supports a minimum of 1 and a

 

 

 

 

 

maximum of 12 entries. Each entry contains the IP address

 

 

 

 

 

and the port number.

 

 

 

 

 

The hostlist is disabled for Manual and Modem Modes. The

 

 

 

 

 

unit does not accept a data connection from a remote

 

 

 

 

 

device when the hostlist option is enabled.

 

 

 

 

 

 

 

UDS2100 User Guide

46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents UDS2100 User Guide Revisions Copyright & TrademarkContacts Date Rev CommentsContents Setup Mode Server Configuration Warranty Figures TablesChapter Summary Using This GuidePurpose and Audience Chapter DescriptionAdditional Documentation DocumentApplications IntroductionApplication Examples Introduction Configuration Methods Additional FeaturesProtocol Support Product Information Label Sample Hardware Address 00-20-4A-14-01-18 or 00204A140118Package Contents Getting StartedInstalling the UDS To install the unitIP Address Required InformationHardware Address IP Address Subnet Mask GatewayAssigning an IP Address Assigning the IP Address DeviceInstallerInstalling DeviceInstaller Select Assign a specific IP address and click NextTo view the units current settings Accessing the UDS2100 Using DeviceInstallerViewing the Current Configuration Adding the Unit to the Manage ListSetting Getting StartedNext Step To configure the unit using a Telnet sessionPress Enter within 5 seconds Assigning the IP Address Serial Port Login Configuration Using Web Manager Accessing UDS2100 Using DeviceInstallerNetwork Configuration Lantronix Web ManagerTo assign an IP address automatically Automatic IP Address ConfigurationSelect Obtain IP address automatically Select Use the following IP configuration Static IP Address ConfigurationEthernet Configuration To assign an IP address manuallyServer Configuration Server ConfigurationTo configure the UDS2100’s device server settings AdvancedHost List Configuration To configure the host listRetry Settings Channel 1 and Channel 2 ConfigurationSerial Settings Host InformationPort Settings ChannelPack Control Flush Input Buffer Serial to NetworkTo configure a channel’s TCP settings Connection Settings TCPFlush Output Buffer Network to Serial Endpoint Configuration Connect Mode Passive ConnectionConnect Mode Active Connection Connect ProtocolDisconnect Mode Common OptionsTo configure a channel’s UDP settings Connection Settings UDPDatagram Mode Apply Settings Apply Factory DefaultsAccessing Setup Mode Configuration via Telnet or Serial Port Setup ModeTelnet Connection Serial Port Connection To establish a Telnet connectionExiting Setup Mode To exit setup modeIP Address Setup Mode Server ConfigurationServer Configuration Option Set Gateway IP AddressDhcp Name Change Telnet Configuration PasswordNetmask Number of Bits for Host Part Network Class Host Bits NetmaskSetup Mode Server Configuration Channel 1 Option Setup Mode Channel ConfigurationBaudrate Common I/F Mode Setting Binary Interface ModeMode Option Flow Flow Control Option Hex Connect Mode Port Number Port Numbers Reserved forConnect Mode Option Response Incoming ConnectionActive Startup Manual Connection Address Example To enable the hostlist Datagram TypeModem Mode MessageMeaning No CarrierModem Mode Function Command Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Remote Port Disconnect Mode OptionRemote IP Address DisConnModeFlush Mode Buffer Flushing Pack ControlSend Characters Packing IntervalTrailing Characters OptionSend Characters DisConnTime Inactivity TimeoutChannel Port Password Telnet Terminal TypeExpert Settings Option Setup Mode Advanced SettingsTCP Keepalive time in seconds Enable alternate MAC ARP Cache timeout in secondsDisable Monitor Mode at bootup Http Port NumberDisable Telnet Setup Security Settings OptionDisable Snmp Snmp Community NameDisable Web Server Disable Tftp Firmware UpdateDisable Port 77FE Hex Disable Web SetupExpert Settings Defaults Default Settings OptionChannel 1 and Channel 2 Configuration Defaults Security Settings DefaultsSetup Mode Advanced Settings Obtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface ROM FileUsing Tftp Command Line Interface To recover firmwareFirmware Upgrades Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port Monitor Mode CommandsCommand Command Name Function Response MeaningTroubleshooting and Contact Information LEDsDiagnostic, Power, and Serial Port LEDs UDS2100 LEDs LEDs MeaningProblems and Error Messages Problem/Message Reason SolutionProblem/Message Reason Solution Technical Support Technical Support Europe, Middle East, and AfricaConnections and Pinouts Serial Connector PinoutsUDS2100 Serial Ports To reset the unit to factory defaults Reset ButtonEthernet Connector Pinouts Power Plug Network PortTechnical Specifications Category DescriptionCategory Description Transient over voltages Alternative Ways to Assign an IP Address AutoIPARP and Telnet To assign a temporary IP addressConversion Table Converting Binary to HexadecimalDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index
Top Page Image Contents