Lantronix 900-588 manual Lantronix Corporate Headquarters, Technical Support Sales Offices

Page 2

Copyright and Trademark

© 2013 Lantronix, Inc. All rights reserved. No part of the contents of this book may be transmitted or reproduced in any form or by any means without the written permission of Lantronix, Inc.

Lantronix® and DeviceLinx® are registered trademarks of Lantronix, Inc. DeviceInstaller™ is a trademark of Lantronix, Inc.

Windows® and Internet Explorer® are registered trademarks of Microsoft Corporation Mozilla® and Firefox® are registered trademarks of the Mozilla Foundation. Chrome™ is a trademark of Google, Inc. All other trademarks and trade names are the property of their respective holders.

Warranty

For details on the Lantronix warranty replacement policy, please go to our Web site at www.lantronix.com/support/warranty.

Contacts

Lantronix Corporate Headquarters

167 Technology Drive

Irvine, CA 92618, USA

Toll Free: 800-526-8766

Phone: 949-453-3990

Fax: 949-450-7249

Technical Support

Online: www.lantronix.com/support

Sales Offices

For a current list of our domestic and international sales offices, go to the Lantronix web site at www.lantronix.com/about/contact.

Disclaimer

Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his or her own expense, will be required to take whatever measures may be required to correct the interference.

Note: Changes or modifications to this device not explicitly approved by Lantronix will void the user's authority to operate this device.

Revision History

Date

Rev.

Firmware

Comments

 

 

 

 

March 2011

A

6.7.0.2

Initial release

 

 

 

 

March 2013

B

6.8.0.4

Updated for firmware release 6.8.0.4.

 

 

 

 

For the latest revision of this product document, please check our online documentation at www.lantronix.com/support/documentation.

Micro125 User Guide

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents User Guide Technical Support Sales Offices Lantronix Corporate HeadquartersTechnology Drive Irvine, CA 92618, USA Toll Free Phone Fax Date Rev Firmware CommentsTable of Contents Configuration via Telnet or Serial Port Setup Mode Setup Mode Advanced Settings Problems and Error Messages Technical SupportList of Figures List of TablesChapter Summary Using This GuidePurpose and Audience Remaining chapters in this guide includeDocument Description DeviceInstaller Online HelpAdditional Documentation Micro125 Integration GuideApplications IntroductionCapabilities Addresses and Port Numbers Configuration MethodsProtocol Support Hardware AddressIP Address Port NumbersRequired Information Physically Connecting the UnitGetting Started 10/100 EthernetGetting Started To install DeviceInstaller Using DeviceInstallerInstalling DeviceInstaller Assigning an IP AddressDeviceInstaller provides a view of the units configuration Accessing the Micro125 Using DeviceInstallerViewing the Current Configuration To view the units current settingsType CommentsDevice Family Hardware AddressSetup Supports 230K Baud UpgradeableConfigurable Pins FirmwareConfiguration Using Web Manager Accessing Web-Manager Using DeviceInstallerWeb-Manager Login Window Lantronix Web-ManagerAutomatic IP Address Configuration Network ConfigurationNetwork Mode Select Obtain IP address automaticallyEnter the following as necessary Static IP Address ConfigurationSelect Use the following IP configuration To assign an IP address manuallyTo specify how data will be transmitted Ethernet ConfigurationEthernet Settings Description Auto NegotiateServer Configuration Description Settings Server ConfigurationTo configure the Micro125’s device server settings Advanced Settings Description Host List ConfigurationTo configure the Micro125’s host list On the main menu, click HostlistRetry Settings Description Channel 1 and Channel 2 ConfigurationRetry Settings Host InformationChannel Setting Description Serial SettingsTo configure the channel’s serial settings Port Settings DescriptionPack Control Settings Description With Active Connect Flush Input Buffer Settings DescriptionFlush Output Buffer Description Settings With Passive ConnectConnection Settings TCP To configure a channel’s TCP settingsActive Connection Mode Description Settings Connect Protocol Setting DescriptionPassive Connection Mode Description Settings Available fields, enter or modify the following informationDisconnect Mode Settings Description Endpoint Configuration Description SettingsCommon Option Settings Description Inactivity Timeout Connection Settings UDPTo configure a channel’s UDP settings Check EOT Ctrl-DConnection Protocol Description Apply SettingsDatagram Mode Description Settings Apply Defaults Applying SettingsTelnet Connection Configuration via Telnet or Serial Port Setup ModeAccessing Setup Mode Click OK. The following information displays Serial Port ConnectionTo establish a Telnet connection Exiting Setup Mode To exit setup mode, utilize one of the following two optionsThis chapter explains how to configure the network settings Setup Mode Server ConfigurationServer Configuration Option IP AddressSet DNS Server IP Address Set Gateway IP AddressNetmask Number of Bits for Host Part Standard IP Network NetmasksChange Telnet/Web-Manager Password Dhcp NameBaudrate Setup Mode Channel ConfigurationChannels Mode Option Interface ModeFollowing table displays available I/F Mode options Common I/F Mode Setting Binary HexUse the following table to select flow control options FlowPort Number Connect Mode Options Connect ModeEnter Connect Mode options in hexadecimal notation Connect Mode OptionResponse Active StartupC28.10/12 Manual Connection Address ExampleC121.2.4.5/1 C0.0.0.0/0To enable the hostlist Hostlist OptionDatagram Type Modem ModeModem Mode Description Datagram Type DescriptionMessage Meaning Modem Mode MessagesFull Verbose Command was executed without error Network connection has been establishedSend the Escape Sequence +++ in Modem Mode Modem Mode Function CommandRemote IP Address Show IP addr after RingAuto Increment Source Port Remote Port11. Disconnect Mode Options Disconnect Mode OptionOption Flush Mode Buffer FlushingPack Control Trailing Characters DisConnTime Inactivity TimeoutPacking Interval Send CharactersTelnet Terminal Type Channel Port PasswordSend Characters Default settings are listed below Setup Mode Advanced SettingsExpert Settings Option Device Details Settings DescriptionTCP Re-transmission Timeout ARP Cache Timeout in SecondsDisable Monitor Mode at Bootup Enable Alternate MACDisable Telnet Setup Security Settings OptionDisable Snmp Select 6 to configure security settingsDisable Web Server Disable Tftp Firmware UpgradeDisable Port 77FE Hex Disable Web SetupEnable Enhanced Password To configure AES encryption on the Micro125Expert Settings Defaults Default Settings OptionChannel 1 and Channel 2 Configuration Defaults Channel Setting Default ConfigurationSecurity Settings Defaults Security Setting Default ConfigurationObtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface To download new firmware from a computerUsing Tftp Command Line Interface Firmware UpgradesTo recover firmware Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port Monitor Mode CommandsG0, G1, ....,Ge, Gf Monitor Mode CommandsCommand Command Name Function S0, S1,...,Se, SfResponse Meaning Problem/Message Reason Solution TroubleshootingProblems and Error Messages Troubleshooting Caps Lock is not onCorrectly to make a good socket Phone 800 422-7044 US Only 949 Technical SupportTechnical Support US Technical Support Europe, Middle East, and AfricaConversion Table Binary to Hexadecimal ConversionsConverting Binary to Hexadecimal Decimal Binary HexScientific Calculator
Top Page Image Contents