Lantronix Ethernet manual Flush Mode Buffer Flushing, Pack Control

Page 61

Setup Mode: Channel Configuration

(3)The TCP connection closes even if the remote site does not acknowledge the disconnection.

(4)When there is a network connection to or from the serial port, the state LED turns off instead of blinking.

(5)When Ctrl+D or Hex 04 is detected, the connection is dropped. Both EOT must be enabled for Disconnect with EOT to function properly. the serial port to the network.

Telnet Mode and Disconnect with Ctrl+D is only detected going from

(6)When DTR transitions from a high state to a low state, the network connection to or from the serial port drops.

Flush Mode (Buffer Flushing)

Using this parameter, you can control line handling and network buffers with connection startup and disconnect. The default setting is 00.

FlushMode (00) ? _

You can also select between two different packing algorithms.

Note: All bit positions in the table that are blank represent “don’t care” bits for that particular option; they can be set to either a 0 or 1 value.

Table 7-8. Flush Mode Options

Function

7

6

5

4

3

2

1

0

 

 

 

 

 

 

 

 

 

Input Buffer (Serial to Network)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Clear with a connection initiated from the device to the network

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

Clear with a connection initiated from the network to the device

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Clear when the network connection to or from the device is disconnected

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Output Buffer (Network to Serial)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Clear with a connection initiated from the device to the network

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

Clear with a connection initiated from the network to the device

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

Clear when the network connection to or from the device is disconnected

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

Alternate Packing Algorithm (Pack Control)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Enable

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pack Control

The packing algorithms define how and when packets are sent to the network. The standard algorithm is optimized for applications in which the unit is used in a local environment, allowing for very small delays for single characters, while keeping the packet count low. The alternate packing algorithm minimizes the packet count on the network and is especially useful in applications in a routed Wide Area Network (WAN). Adjusting parameters in this mode can economize the network data stream.

Pack control settings are enabled in Flush Mode. Set this value to 00 if you do not need specific functions.

Note: All bit positions in the table that are blank represent “don’t care” bits for that particular option; they can be set to either a 0 or 1 value.

WiBox2100E User Guide

61

Page 60 Page 62
Image 61
Page 60 Page 62
Contents WiBox2100E User Guide Technical Support Sales Offices Lantronix Corporate HeadquartersContents Contents Setup Mode Server ConfigurationSetup Mode Advanced Settings Compliance List of TablesSerial Tunneling Infrastructure Network Example List of FiguresPurpose and Audience Using This GuideChapter Summary Additional Documentation Using This GuideApplications IntroductionName Model Part Numbers Serial Tunneling Network Application ExamplesIntroduction Serial Tunneling Infrastructure Ad Hoc NetworkProtocol Support Configuration MethodsAd Hoc WiBox Connection WiBox with EthernetAddresses and Port Numbers Wlan SettingsHardware Address IP AddressDB9M DTE Serial Connector Serial Connector PinoutsWBX2100E Network Interface RS-485 2-Wire PinoutsLEDs Ethernet Connector PinoutsWiBox LEDs Technical Specifications Required Information Quick StartHardware Address 00-20-4a IP Address Subnet Mask GatewayWEP Enabled Y/N? WEP Key 64 bit or 128 bit? Installing and Configuring the WiBoxWPA Enabled Y/N WPA Key Type hex or passphrase? Quick StartSyntax is SetZone IP address zone abbreviation WEP To install the DeviceInstaller Using Device InstallerTo view the WiBox’s configuration settings Viewing the Current ConfigurationRate Supports Wired Ethernet Firmware UpgradeableWebPort Maximum Baud RateQuick Start Accessing Web-Manager through a Web Browser Web-Manager ConfigurationWeb-Manager Configuration Network ConfigurationSelect Obtain IP address automatically Automatic IP Address ConfigurationAuto-IP Dhcp Host NameStatic IP Address Configuration Server ConfigurationEthernet Configuration Select Use the following IP configurationServer Configuration To configure the WiBox’s device server settingsAdvanced To configure the WiBox’s hostlist Hostlist ConfigurationCPU Performance Mode Http Server PortSerial Settings Channel 1 and Channel 2 ConfigurationRetry Settings Host InformationDisable Serial Port Port SettingsChannel ProtocolFlush Input Buffer Serial to Network Pack ControlFlush Output Buffer Network to Serial Connection Settings TCPConnect Protocol At Time of DisconnectConnect Mode Active Connection Connect Mode Passive ConnectionCommon Options Endpoint ConfigurationDisconnect Mode Connection Settings UDPDatagram Type Datagram ModeTo configure the WiBox’s Wlan settings Wlan ConfigurationDevice Address Table Wireless Network Security Wireless Network ConfigurationNetwork Name Network Type Select Infrastructure or Ad Hoc ChannelWEP Options Advanced SettingsWPA Options Applying Defaults Updating SettingsAccessing Setup Mode Telnet or Serial Port Setup Mode ConfigurationTelnet Connection To establish a Telnet connectionTelnet or Serial Port Setup Mode Configuration Exiting Setup ModeTo exit Setup Mode Serial Port ConnectionServer Configuration Option Setup Mode Server ConfigurationNetwork Mode IP AddressSetup Mode Server Configuration Change Telnet Configuration PasswordSet Gateway IP Address Netmask Number of Bits for Host PartDhcp Name Channel 1 Option Setup Mode Channel ConfigurationBaudrate Setup Mode Channel Configuration Interface ModeMode Option Common I/F Mode Setting Binary HexPort Number Connect ModeFlow Control Option Hex Port Numbers Reserved forConnect Mode Options Connect Mode OptionIncoming Connection ResponseResponse Incoming ConnectionActive Startup Manual Connection Address Example Manual ConnectionAutostart Automatic To enable the hostlistConnection HostlistDatagram Type Modem ModeMessage Meaning 11. Modem Mode MessagesFull Verbose Numeric ResponseModem Mode Function Command Send the Escape Sequence +++ in Modem ModeModem Mode Commands Auto Increment Source PortDisconnect Mode Options Disconnect Mode OptionRemote IP Address Remote PortPack Control Flush Mode Buffer FlushingPacking Interval DisConnTime Inactivity TimeoutTrailing Characters Send CharactersWlan Settings Channel Port PasswordSend Characters Telnet Terminal TypeAdhoc Network Channel Network Name SsidSecurity Transmission Data Rate Fixed or Automatic Data RateEnable Power Management Expert Settings Option Setup Mode Advanced SettingsTCP Keepalive time in seconds Disable Monitor Mode at bootup ARP Cache timeout in secondsCPU Performance Http Port NumberSecurity Settings Disable Web Server Disable Port 77FE HexDisable Web Setup Disable Echo PortsGenerally, one of two situations applies Channel 1 Configuration Default SettingsChannel 2 Configuration Security Settings Expert SettingsEnable Power Management Channel SecurityExit Configuration Mode Entering Monitor Mode via the Serial Port Monitor ModeEntering Monitor Mode via the Network Port Monitor Mode CommandsCommand Response Codes Monitor ModeResponse Meaning G0, G1, ....,Ge, GfUpdating Firmware Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware ROM FileUsing Tftp Command Line Interface Network UpgradeUpdating Firmware To download new firmware from a computerSyntax is SetZone IP address zone abbreviation Wlan Country SettingConfiguring the WiBox in Bridging Mode Wireless BridgingMethod Troubleshooting Diagnostic LED States TroubleshootingProblems and Error Messages Problem/Message Reason SolutionLater, there is only one setting for Caps Lock is not on WiBox2100E onlyTechnical Support Europe, Middle East, and Africa Technical SupportConverting Binary to Hexadecimal Binary to Hexadecimal ConversionsConversion Table Scientific CalculatorBinary to Hexadecimal Conversions Compliance Information ComplianceUSA Federal Communications Commission FCC Notice Regulatory InformationCanada Industry Canada Notice ComplianceAustralia & New Zealand Wireless Notice Europe R&TTE Directive 99/5/EC, Wireless NoticeAntenna Notice Exposure of Humans to RF FieldsCompliance Warranty

Ethernet specifications

Lantronix Ethernet technology is a pivotal component in modern networking, facilitating seamless communication and connectivity across a multitude of devices. Renowned for its reliability and innovation, Lantronix offers a diverse range of products and solutions that cater to various industries, from healthcare to industrial automation.

One of the standout features of Lantronix Ethernet devices is their ability to enable remote access and management of equipment. This is particularly beneficial in scenarios where physical access is limited or impractical. With secure remote management, organizations can monitor, control, and configure devices from virtually anywhere, streamlining operations and reducing downtime.

Lantronix Ethernet products utilize advanced technologies such as Serial to Ethernet conversion, which allows legacy serial devices to communicate over an IP network. This feature is essential for companies looking to modernize their infrastructure without the need for a complete overhaul of existing equipment. By bridging the gap between old and new technologies, Lantronix ensures that organizations can extend the lifespan of their investments.

Another key characteristic of Lantronix Ethernet solutions is their robustness and security. Designed to withstand various environmental conditions, these devices are suitable for deployment in harsh environments, making them ideal for industrial applications. Additionally, robust encryption protocols and security features help safeguard sensitive data, ensuring that only authorized personnel can access the system.

Scalability is also a significant advantage of Lantronix Ethernet technology. As businesses grow and evolve, their networking needs often change. Lantronix products are designed to scale easily, allowing organizations to add new devices and functionality without disrupting existing operations. This flexibility enables businesses to adapt to new challenges and opportunities as they arise.

Moreover, Lantronix places a strong emphasis on ease of integration. With extensive support for various communication protocols and interfaces, their Ethernet solutions can be quickly and effectively integrated into existing systems, minimizing deployment time and maximizing efficiency.

In conclusion, Lantronix Ethernet technology represents a comprehensive solution for modern networking needs. With features such as remote management, serial communication capabilities, security, scalability, and ease of integration, Lantronix stands out as a leader in the connectivity landscape, empowering businesses to optimize operations and enhance productivity. Whether in industrial environments or remote locations, Lantronix Ethernet solutions deliver the reliability and performance required in today’s fast-paced digital world.
Top Page Image Contents