Power Supply, LEDs, Safety Precautions | Cisco Systems ASR 901 10G

Chapter 1 Introduction

Figure 1-3

Cisco ASR 901 10G Router—Rear View

2

1

Power Supply

334636

1

Fan

2

Grounding Point Lug

Note The grounding architecture of this product is DC-isolated (DC-I) for DC-powered products. DC-powered products have a nominal operating DC voltage of 48 VDC. Minimal steady state DC operating voltage is 19.2 VDC.

LEDs

The Cisco ASR 901 10G chassis and interface modules contain LEDs to assist in troubleshooting. For more detailed description of the LEDs, see the “Reading the LEDs, page A-4.

Power Supply

The Cisco ASR 901 10G router is equipped with an internal -24/-60 Volts Direct Current (VDC). The router is provided with a single AC power supply or DC (1+1 Redundant) power supply. The power input connectors are located at the front left-side side of the router. The DC power connector has the standard A and B feeds for DC redundancy. The DC power supply is compatible with the range of DC input voltages specifically available at cell sites.

See Table 1-1for the DC power supply specifications and Table 1-2for the AC power supply specifications.

Safety Precautions

Observe the following general safety precautions and recommendations in planning the source power requirements for the Cisco ASR 901 10G router (for additional safety information, see the “Safety Guidelines” section on page 2-1:

•Check the power at your site before router installation (and periodically after installation) to ensure clean power (free of spikes and noise) is being received.

•Always disconnect the power source and unplug the power cable before working on the router.

Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide

	OL-28105-02	1-5

Image 15

Cisco Systems ASR 901 10G manual Power Supply, LEDs, Safety Precautions

Contents

Cisco Systems, Inc Page N T E N T S Site Environment Formatting Flash Memory as a DOS File System Alarm Port Pinouts B-8 Revision Date Change Summary Document Revision History Conventions ObjectivesAudience Organization Related Documentation Safety Warnings OL-28105-02 Hardware Description Introduction Cisco ASR 901 10G Router-Front View of TDM Version Cisco ASR 901 10G Router-Front View of Ethernet Version Cisco ASR 901 Router-Front View of Ethernet Version Cisco ASR 901 10G Router-Rear View Power Supply Safety PrecautionsLEDs Specification Value Cisco ASR 901 10G Router AC Power Supply Specifications Pin Connector a Connector B Environmental Monitoring Temperature Sensor System Specifications Description SpecificationRouter Interface Numbering Cisco ASR 901 10G Router Interface Number Location Label Regulatory Compliance Chapter Safety with Equipment Safety Guidelines Safety with Electricity Preventing Electrostatic Discharge Damage Site Environment Power Supply ConsiderationsPrerequisites Site Planning Air Flow Guidelines Method of Procedure Required Tools and Equipment Unpacking and Checking the Contents of your Shipment Task Verified by Installation Checklist Task Verified by Date Console Port ConsiderationsCreating a Site Log Console Port Connections Preparing to Install the Router Console Port Considerations OL-28105-02 Network Modules Installing the Cisco ASR 901 10G Router Mounting the Cisco ASR 901 10G Router Rack-Mounting Configuration Guidelines Rack-Mounting Brackets Attaching Brackets to the Router Attaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Wall-Mounting Mounting the Cisco ASR 901 10G Router in a Rack Mounting the Router on a Wall Attaching Brackets for Wall-Mounting User-supplied screws Grounding the Cisco ASR 901 10G Router Connecting the Chassis Ground and Power Stripping a Ground Wire Power Connection Compliance Wiring the DC-Input Power Source 10 3-Pin Terminal Block Installing the DC Power Cord Retainer DC power cord 13 Inserting the Retainer through the Lanced Loop Installing the AC Power Cord Retainer Sleeve for thin power cords AC power cord Installing SFP Modules Installing and Removing SFP Modules 18 SFP Module with a Bale-Clasp Latch Removing SFP Modules Console Port Connecting CablesConnecting the Console Port Types of RJ-45 Cables Connecting the Network Cables Connecting Gigabit Ethernet Interface CablesConnecting T1 and E1 Interface Cables Connecting SFP Cables Connecting Cables to the Bits InterfaceConnecting GPS Cables Connecting to Alarm Port Connecting to the Management Ethernet PortDressing Router Cables Interpreting Front-Panel LEDs Powering on the RouterChecklist for Power on Power-On Procedure Copying Files Formatting Procedures for Flash MemoryFile and Directory Procedures Formatting Flash Memory as a DOS File System Deleting Files from the Flash Memory Displaying Contents of the Flash Memory Enter a Directory and Determine the Current Directory Displaying File Content What to Do After Installing the Hardware Problem Solving Troubleshooting Troubleshooting the Power and Cooling Systems Environmental Reporting FeaturesSymptom Possible Cause Corrective Action Information Packet publication Troubleshooting Cables and Connections Reading the LEDs Chassis LEDsColor/State Location Description Color/State Description two LEDs for each T1/E1 port T1/E1 Interface LEDsSFP Ethernet Interface LEDs 10G SFP+ Ethernet Interface LEDs RJ-45 Ethernet Interface LEDs Gigabit Ethernet Connector Pinouts Cable Specifications SFP and SFP+ Port Pinouts and Cable Specifications Pin FE Signal GE SignalT1/E1 Port Pinouts Pin Signal Name Direction Description Console Port Signals and Pinouts Console Port Signals and Pinouts Pin Signal Name HP Pins Direction DescriptionRJ-45-to-DB-9 Terminal Adapter Console Terminal Adapter Device Signal RJ-45 Pin DB-25 Pin Identifying a Rollover CableConsole RJ-45-to-DB-25 Port DTE Time of Day Pinouts Bits Port Pinouts 10 Mhz GPS Port Pinouts Pin Signal Name Description Alarm Port Pinouts Auxiliary Port Management Ethernet Port Pinouts OL-28105-02 Site Log Initials Date Numerics IN-2 IN-3 IN-4