User-supplied screws | Cisco Systems ASR 901 10G instruction

Chapter 3 Installing the Cisco ASR 901 10G Router

Mounting the Cisco ASR 901 10G Router

For the best support of the router and cables, make sure that the switch is attached securely to wall studs or to a firmly attached plywood mounting backboard.

Perform the steps given below:

Warning Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378

Step 1 Locate the position where you plan to install the router.

Step 2 Ensure that there are no obstructions.

Step 3 Position the router with the ports facing up as in Figure 3-6, or down and align the bracket holes with the holes on the wall and secure with four Number 6-32 x 0.25-inch mounting screws (two on each side).

Step 4 Tighten the screws using a 1/4-inch flat-blade screwdriver (each side).

Figure 3-6 Mounting the Router on a Wall

1

334584

1

User-supplied screws

2

—

Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide

	OL-28105-02	3-9

Image 41

Cisco Systems ASR 901 10G manual User-supplied screws

Contents

Cisco Systems, Inc Page N T E N T S Site Environment Formatting Flash Memory as a DOS File System Alarm Port Pinouts B-8 Revision Date Change Summary Document Revision History Audience ObjectivesOrganization Conventions Related Documentation Safety Warnings OL-28105-02 Hardware Description Introduction Cisco ASR 901 10G Router-Front View of TDM Version Cisco ASR 901 10G Router-Front View of Ethernet Version Cisco ASR 901 Router-Front View of Ethernet Version Cisco ASR 901 10G Router-Rear View LEDs Power SupplySafety Precautions Specification Value Cisco ASR 901 10G Router AC Power Supply Specifications Pin Connector a Connector B Environmental Monitoring Temperature Sensor Router Interface Numbering System SpecificationsDescription Specification Cisco ASR 901 10G Router Interface Number Location Label Regulatory Compliance Chapter Safety with Equipment Safety Guidelines Safety with Electricity Preventing Electrostatic Discharge Damage Prerequisites Power Supply ConsiderationsSite Planning Site Environment Air Flow Guidelines Method of Procedure Required Tools and Equipment Unpacking and Checking the Contents of your Shipment Task Verified by Installation Checklist Creating a Site Log Console Port ConsiderationsConsole Port Connections Task Verified by Date Preparing to Install the Router Console Port Considerations OL-28105-02 Network Modules Installing the Cisco ASR 901 10G Router Mounting the Cisco ASR 901 10G Router Rack-Mounting Configuration Guidelines Rack-Mounting Brackets Attaching Brackets to the Router Attaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Wall-Mounting Mounting the Cisco ASR 901 10G Router in a Rack Mounting the Router on a Wall Attaching Brackets for Wall-Mounting User-supplied screws Grounding the Cisco ASR 901 10G Router Connecting the Chassis Ground and Power Stripping a Ground Wire Power Connection Compliance Wiring the DC-Input Power Source 10 3-Pin Terminal Block Installing the DC Power Cord Retainer DC power cord 13 Inserting the Retainer through the Lanced Loop Installing the AC Power Cord Retainer Sleeve for thin power cords AC power cord Installing SFP Modules Installing and Removing SFP Modules 18 SFP Module with a Bale-Clasp Latch Removing SFP Modules Connecting the Console Port Connecting CablesTypes of RJ-45 Cables Console Port Connecting T1 and E1 Interface Cables Connecting the Network CablesConnecting Gigabit Ethernet Interface Cables Connecting GPS Cables Connecting SFP CablesConnecting Cables to the Bits Interface Dressing Router Cables Connecting to Alarm PortConnecting to the Management Ethernet Port Checklist for Power on Powering on the RouterPower-On Procedure Interpreting Front-Panel LEDs File and Directory Procedures Formatting Procedures for Flash MemoryFormatting Flash Memory as a DOS File System Copying Files Deleting Files from the Flash Memory Displaying Contents of the Flash Memory Enter a Directory and Determine the Current Directory Displaying File Content What to Do After Installing the Hardware Problem Solving Troubleshooting Symptom Possible Cause Corrective Action Troubleshooting the Power and Cooling SystemsEnvironmental Reporting Features Information Packet publication Troubleshooting Cables and Connections Color/State Location Description Reading the LEDsChassis LEDs SFP Ethernet Interface LEDs T1/E1 Interface LEDs10G SFP+ Ethernet Interface LEDs Color/State Description two LEDs for each T1/E1 port RJ-45 Ethernet Interface LEDs Gigabit Ethernet Connector Pinouts Cable Specifications T1/E1 Port Pinouts SFP and SFP+ Port Pinouts and Cable SpecificationsPin FE Signal GE Signal Pin Signal Name Direction Description Console Port Signals and Pinouts RJ-45-to-DB-9 Terminal Adapter Console Console Port Signals and PinoutsPin Signal Name HP Pins Direction Description Console RJ-45-to-DB-25 Port DTE Terminal Adapter Device Signal RJ-45 Pin DB-25 PinIdentifying a Rollover Cable Time of Day Pinouts Bits Port Pinouts 10 Mhz GPS Port Pinouts Pin Signal Name Description Alarm Port Pinouts Auxiliary Port Management Ethernet Port Pinouts OL-28105-02 Site Log Initials Date Numerics IN-2 IN-3 IN-4