Installing the Cisco ASR 901 10G Router | Cisco Systems specs

C H A P T E R 3

Installing the Cisco ASR 901 10G Router

This chapter describes how to install the Cisco ASR 901 10G router, and how to connect it to external devices. These are the following sections:

•Network Modules, page 3-1

•Mounting the Cisco ASR 901 10G Router, page 3-2

•Connecting the Chassis Ground and Power, page 3-10

•Installing and Removing SFP Modules, page 3-17

•Connecting Cables, page 3-20

•Powering on the Router, page 3-24

Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030

Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security.

Statement 1017

Network Modules

You can order the Cisco ASR 901 10G router with the following interface modules.

•T1/E1 interface module

•SFP Ethernet interface module

•RJ-45 Ethernet interface module

Note Interface modules are installed and shipped with the router; they are not field replaceable.

Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide

	OL-28105-02	3-1

Image 33

Cisco Systems manual Installing the Cisco ASR 901 10G Router, Network Modules

Contents

Cisco Systems, Inc Page N T E N T S Site Environment Formatting Flash Memory as a DOS File System Alarm Port Pinouts B-8 Revision Date Change Summary Document Revision History Audience ObjectivesOrganization Conventions Related Documentation Safety Warnings OL-28105-02 Hardware Description Introduction Cisco ASR 901 10G Router-Front View of TDM Version Cisco ASR 901 10G Router-Front View of Ethernet Version Cisco ASR 901 Router-Front View of Ethernet Version Cisco ASR 901 10G Router-Rear View Power Supply Safety PrecautionsLEDs Specification Value Cisco ASR 901 10G Router AC Power Supply Specifications Pin Connector a Connector B Environmental Monitoring Temperature Sensor System Specifications Description SpecificationRouter Interface Numbering Cisco ASR 901 10G Router Interface Number Location Label Regulatory Compliance Chapter Safety with Equipment Safety Guidelines Safety with Electricity Preventing Electrostatic Discharge Damage Prerequisites Power Supply ConsiderationsSite Planning Site Environment Air Flow Guidelines Method of Procedure Required Tools and Equipment Unpacking and Checking the Contents of your Shipment Task Verified by Installation Checklist Creating a Site Log Console Port ConsiderationsConsole Port Connections Task Verified by Date Preparing to Install the Router Console Port Considerations OL-28105-02 Network Modules Installing the Cisco ASR 901 10G Router Mounting the Cisco ASR 901 10G Router Rack-Mounting Configuration Guidelines Rack-Mounting Brackets Attaching Brackets to the Router Attaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Wall-Mounting Mounting the Cisco ASR 901 10G Router in a Rack Mounting the Router on a Wall Attaching Brackets for Wall-Mounting User-supplied screws Grounding the Cisco ASR 901 10G Router Connecting the Chassis Ground and Power Stripping a Ground Wire Power Connection Compliance Wiring the DC-Input Power Source 10 3-Pin Terminal Block Installing the DC Power Cord Retainer DC power cord 13 Inserting the Retainer through the Lanced Loop Installing the AC Power Cord Retainer Sleeve for thin power cords AC power cord Installing SFP Modules Installing and Removing SFP Modules 18 SFP Module with a Bale-Clasp Latch Removing SFP Modules Connecting the Console Port Connecting CablesTypes of RJ-45 Cables Console Port Connecting the Network Cables Connecting Gigabit Ethernet Interface CablesConnecting T1 and E1 Interface Cables Connecting SFP Cables Connecting Cables to the Bits InterfaceConnecting GPS Cables Connecting to Alarm Port Connecting to the Management Ethernet PortDressing Router Cables Checklist for Power on Powering on the RouterPower-On Procedure Interpreting Front-Panel LEDs File and Directory Procedures Formatting Procedures for Flash MemoryFormatting Flash Memory as a DOS File System Copying Files Deleting Files from the Flash Memory Displaying Contents of the Flash Memory Enter a Directory and Determine the Current Directory Displaying File Content What to Do After Installing the Hardware Problem Solving Troubleshooting Troubleshooting the Power and Cooling Systems Environmental Reporting FeaturesSymptom Possible Cause Corrective Action Information Packet publication Troubleshooting Cables and Connections Reading the LEDs Chassis LEDsColor/State Location Description SFP Ethernet Interface LEDs T1/E1 Interface LEDs10G SFP+ Ethernet Interface LEDs Color/State Description two LEDs for each T1/E1 port RJ-45 Ethernet Interface LEDs Gigabit Ethernet Connector Pinouts Cable Specifications SFP and SFP+ Port Pinouts and Cable Specifications Pin FE Signal GE SignalT1/E1 Port Pinouts Pin Signal Name Direction Description Console Port Signals and Pinouts Console Port Signals and Pinouts Pin Signal Name HP Pins Direction DescriptionRJ-45-to-DB-9 Terminal Adapter Console Terminal Adapter Device Signal RJ-45 Pin DB-25 Pin Identifying a Rollover CableConsole RJ-45-to-DB-25 Port DTE Time of Day Pinouts Bits Port Pinouts 10 Mhz GPS Port Pinouts Pin Signal Name Description Alarm Port Pinouts Auxiliary Port Management Ethernet Port Pinouts OL-28105-02 Site Log Initials Date Numerics IN-2 IN-3 IN-4