Cisco Systems ASR 901 10G instruction

Chapter 2 Preparing to Install the Router

Console Port Considerations

As a console port, hardware flow control is not supported. For instructions on installing a console terminal, see the “Connecting the Console Port” section on page 3-20.

For cable and port pinouts, see the online document Cisco Modular Access Router Cable Specifications. This document is provided on the documentation DVD that accompanied your router (if ordered).

Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide

	OL-28105-02	2-9

Image 31

Cisco Systems ASR 901 10G manual Preparing to Install the Router Console Port Considerations

Contents

Cisco Systems, Inc Page N T E N T S Site Environment Formatting Flash Memory as a DOS File System Alarm Port Pinouts B-8 Revision Date Change Summary Document Revision History Conventions ObjectivesAudience Organization Related Documentation Safety Warnings OL-28105-02 Hardware Description Introduction Cisco ASR 901 10G Router-Front View of TDM Version Cisco ASR 901 10G Router-Front View of Ethernet Version Cisco ASR 901 Router-Front View of Ethernet Version Cisco ASR 901 10G Router-Rear View Safety Precautions Power SupplyLEDs Specification Value Cisco ASR 901 10G Router AC Power Supply Specifications Pin Connector a Connector B Environmental Monitoring Temperature Sensor Description Specification System SpecificationsRouter Interface Numbering Cisco ASR 901 10G Router Interface Number Location Label Regulatory Compliance Chapter Safety with Equipment Safety Guidelines Safety with Electricity Preventing Electrostatic Discharge Damage Site Environment Power Supply ConsiderationsPrerequisites Site Planning Air Flow Guidelines Method of Procedure Required Tools and Equipment Unpacking and Checking the Contents of your Shipment Task Verified by Installation Checklist Task Verified by Date Console Port ConsiderationsCreating a Site Log Console Port Connections Preparing to Install the Router Console Port Considerations OL-28105-02 Network Modules Installing the Cisco ASR 901 10G Router Mounting the Cisco ASR 901 10G Router Rack-Mounting Configuration Guidelines Rack-Mounting Brackets Attaching Brackets to the Router Attaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Wall-Mounting Mounting the Cisco ASR 901 10G Router in a Rack Mounting the Router on a Wall Attaching Brackets for Wall-Mounting User-supplied screws Grounding the Cisco ASR 901 10G Router Connecting the Chassis Ground and Power Stripping a Ground Wire Power Connection Compliance Wiring the DC-Input Power Source 10 3-Pin Terminal Block Installing the DC Power Cord Retainer DC power cord 13 Inserting the Retainer through the Lanced Loop Installing the AC Power Cord Retainer Sleeve for thin power cords AC power cord Installing SFP Modules Installing and Removing SFP Modules 18 SFP Module with a Bale-Clasp Latch Removing SFP Modules Console Port Connecting CablesConnecting the Console Port Types of RJ-45 Cables Connecting Gigabit Ethernet Interface Cables Connecting the Network CablesConnecting T1 and E1 Interface Cables Connecting Cables to the Bits Interface Connecting SFP CablesConnecting GPS Cables Connecting to the Management Ethernet Port Connecting to Alarm PortDressing Router Cables Interpreting Front-Panel LEDs Powering on the RouterChecklist for Power on Power-On Procedure Copying Files Formatting Procedures for Flash MemoryFile and Directory Procedures Formatting Flash Memory as a DOS File System Deleting Files from the Flash Memory Displaying Contents of the Flash Memory Enter a Directory and Determine the Current Directory Displaying File Content What to Do After Installing the Hardware Problem Solving Troubleshooting Environmental Reporting Features Troubleshooting the Power and Cooling SystemsSymptom Possible Cause Corrective Action Information Packet publication Troubleshooting Cables and Connections Chassis LEDs Reading the LEDsColor/State Location Description Color/State Description two LEDs for each T1/E1 port T1/E1 Interface LEDsSFP Ethernet Interface LEDs 10G SFP+ Ethernet Interface LEDs RJ-45 Ethernet Interface LEDs Gigabit Ethernet Connector Pinouts Cable Specifications Pin FE Signal GE Signal SFP and SFP+ Port Pinouts and Cable SpecificationsT1/E1 Port Pinouts Pin Signal Name Direction Description Console Port Signals and Pinouts Pin Signal Name HP Pins Direction Description Console Port Signals and PinoutsRJ-45-to-DB-9 Terminal Adapter Console Identifying a Rollover Cable Terminal Adapter Device Signal RJ-45 Pin DB-25 PinConsole RJ-45-to-DB-25 Port DTE Time of Day Pinouts Bits Port Pinouts 10 Mhz GPS Port Pinouts Pin Signal Name Description Alarm Port Pinouts Auxiliary Port Management Ethernet Port Pinouts OL-28105-02 Site Log Initials Date Numerics IN-2 IN-3 IN-4