Manuals / Cisco Systems / Power Tools / Saw

Cisco Systems ASR 901 10G manual Cable Specifications, Gigabit Ethernet Connector Pinouts

Models: ASR 901 10G

1 82

Download 82 pages 24.71 Kb

Page 67

A P P E N D I X B

Cable Specifications

If you prefer to build your own cables, this appendix provides cable specifications for the

Cisco ASR 901 10G router.

The appendix includes the following sections:

•Gigabit Ethernet Connector Pinouts, page B-1

•SFP and SFP+ Port Pinouts and Cable Specifications, page B-2

•T1/E1 Port Pinouts, page B-2

•Console Port Signals and Pinouts, page B-3

•BITS Port Pinouts, page B-6

•Time of Day Pinouts, page B-6

•GPS Port Pinouts, page B-7

•Alarm Port Pinouts, page B-8

•Management Ethernet Port Pinouts, page B-9

•Auxiliary Port, page B-9

Warning To comply with the Telcordia GR-1089 NEBS standard for electromagnetic compatibility and safety, use only shielded cables that are grounded on both ends for Type 2 and Type 4 ports that require shielded cables.

Gigabit Ethernet Connector Pinouts

This section illustrates the Gigabit Ethernet RJ-45 connector and lists its pinout and signal descriptions.

Note The RJ-45 ports are capable of operating in both 100BaseT and 1000BaseT modes.

Figure B-1shows the RJ-45 connector and port, and Table B-1lists the connector pinouts and signals.

Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide

	OL-28105-02	B-1

Image 67

Cisco Systems ASR 901 10G manual Cable Specifications, Gigabit Ethernet Connector Pinouts

Contents

Cisco Systems, Inc Page N T E N T S Site Environment Formatting Flash Memory as a DOS File System Alarm Port Pinouts B-8 Revision Date Change Summary Document Revision HistoryConventions ObjectivesAudience OrganizationRelated Documentation Safety WarningsOL-28105-02 Hardware Description IntroductionCisco ASR 901 10G Router-Front View of TDM Version Cisco ASR 901 10G Router-Front View of Ethernet Version Cisco ASR 901 Router-Front View of Ethernet Version Cisco ASR 901 10G Router-Rear ViewSafety Precautions Power SupplyLEDs Specification Value Cisco ASR 901 10G Router AC Power Supply Specifications Pin Connector a Connector B Environmental Monitoring Temperature SensorDescription Specification System SpecificationsRouter Interface Numbering Cisco ASR 901 10G Router Interface Number Location Label Regulatory ComplianceChapter Safety with Equipment Safety GuidelinesSafety with Electricity Preventing Electrostatic Discharge Damage Site Environment Power Supply ConsiderationsPrerequisites Site PlanningAir Flow Guidelines Method of ProcedureRequired Tools and Equipment Unpacking and Checking the Contents of your ShipmentTask Verified by Installation ChecklistTask Verified by Date Console Port ConsiderationsCreating a Site Log Console Port ConnectionsPreparing to Install the Router Console Port Considerations OL-28105-02 Network Modules Installing the Cisco ASR 901 10G RouterMounting the Cisco ASR 901 10G Router Rack-Mounting Configuration GuidelinesRack-Mounting Brackets Attaching Brackets to the RouterAttaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Wall-Mounting Mounting the Cisco ASR 901 10G Router in a RackMounting the Router on a Wall Attaching Brackets for Wall-MountingUser-supplied screws Grounding the Cisco ASR 901 10G Router Connecting the Chassis Ground and PowerStripping a Ground Wire Power Connection Compliance Wiring the DC-Input Power Source 10 3-Pin Terminal Block Installing the DC Power Cord RetainerDC power cord 13 Inserting the Retainer through the Lanced Loop Installing the AC Power Cord RetainerSleeve for thin power cords AC power cord Installing SFP Modules Installing and Removing SFP Modules18 SFP Module with a Bale-Clasp Latch Removing SFP Modules Console Port Connecting CablesConnecting the Console Port Types of RJ-45 CablesConnecting Gigabit Ethernet Interface Cables Connecting the Network CablesConnecting T1 and E1 Interface Cables Connecting Cables to the Bits Interface Connecting SFP CablesConnecting GPS Cables Connecting to the Management Ethernet Port Connecting to Alarm PortDressing Router Cables Interpreting Front-Panel LEDs Powering on the RouterChecklist for Power on Power-On ProcedureCopying Files Formatting Procedures for Flash MemoryFile and Directory Procedures Formatting Flash Memory as a DOS File SystemDeleting Files from the Flash Memory Displaying Contents of the Flash MemoryEnter a Directory and Determine the Current Directory Displaying File ContentWhat to Do After Installing the Hardware Problem Solving TroubleshootingEnvironmental Reporting Features Troubleshooting the Power and Cooling SystemsSymptom Possible Cause Corrective Action Information Packet publication Troubleshooting Cables and ConnectionsChassis LEDs Reading the LEDsColor/State Location Description Color/State Description two LEDs for each T1/E1 port T1/E1 Interface LEDsSFP Ethernet Interface LEDs 10G SFP+ Ethernet Interface LEDsRJ-45 Ethernet Interface LEDs Gigabit Ethernet Connector Pinouts Cable SpecificationsPin FE Signal GE Signal SFP and SFP+ Port Pinouts and Cable SpecificationsT1/E1 Port Pinouts Pin Signal Name Direction Description Console Port Signals and PinoutsPin Signal Name HP Pins Direction Description Console Port Signals and PinoutsRJ-45-to-DB-9 Terminal Adapter Console Identifying a Rollover Cable Terminal Adapter Device Signal RJ-45 Pin DB-25 PinConsole RJ-45-to-DB-25 Port DTE Time of Day Pinouts Bits Port Pinouts10 Mhz GPS Port PinoutsPin Signal Name Description Alarm Port PinoutsAuxiliary Port Management Ethernet Port PinoutsOL-28105-02 Site Log Initials DateNumerics IN-2 IN-3 IN-4