Attaching Brackets for 19-Inch Racks | Cisco Systems ASR 901 10G

Chapter 3 Installing the Cisco ASR 901 10G Router

Mounting the Cisco ASR 901 10G Router

Attaching Brackets for 19-Inch Racks

Figure 3-2shows how to attach brackets for 19-inch racks on the router.

Figure 3-2 Attaching Brackets for 19-Inch Racks

1

2

3

		4
			334578
1	Phillips flat-head screws	2	Front-mounting position
3	Mid-mounting position	4	Rear-mounting position

Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide

3-4	OL-28105-02

Image 36

Cisco Systems ASR 901 10G manual Attaching Brackets for 19-Inch Racks

Contents

Cisco Systems, Inc Page N T E N T S Site Environment Formatting Flash Memory as a DOS File System Alarm Port Pinouts B-8 Document Revision History Revision Date Change Summary Objectives AudienceOrganization Conventions Safety Warnings Related Documentation OL-28105-02 Introduction Hardware Description Cisco ASR 901 10G Router-Front View of TDM Version Cisco ASR 901 10G Router-Front View of Ethernet Version Cisco ASR 901 10G Router-Rear View Cisco ASR 901 Router-Front View of Ethernet Version Power Supply Safety PrecautionsLEDs Specification Value Cisco ASR 901 10G Router AC Power Supply Specifications Environmental Monitoring Temperature Sensor Pin Connector a Connector B System Specifications Description SpecificationRouter Interface Numbering Cisco ASR 901 10G Router Regulatory Compliance Interface Number Location Label Chapter Safety Guidelines Safety with Equipment Safety with Electricity Preventing Electrostatic Discharge Damage Power Supply Considerations PrerequisitesSite Planning Site Environment Method of Procedure Air Flow Guidelines Unpacking and Checking the Contents of your Shipment Required Tools and Equipment Installation Checklist Task Verified by Console Port Considerations Creating a Site LogConsole Port Connections Task Verified by Date Preparing to Install the Router Console Port Considerations OL-28105-02 Installing the Cisco ASR 901 10G Router Network Modules Rack-Mounting Configuration Guidelines Mounting the Cisco ASR 901 10G Router Attaching Brackets to the Router Rack-Mounting Brackets Attaching Brackets for 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets for Etsi Racks Mounting the Cisco ASR 901 10G Router in a Rack Wall-Mounting Attaching Brackets for Wall-Mounting Mounting the Router on a Wall User-supplied screws Connecting the Chassis Ground and Power Grounding the Cisco ASR 901 10G Router Stripping a Ground Wire Power Connection Compliance Wiring the DC-Input Power Source Installing the DC Power Cord Retainer 10 3-Pin Terminal Block DC power cord Installing the AC Power Cord Retainer 13 Inserting the Retainer through the Lanced Loop Sleeve for thin power cords AC power cord Installing and Removing SFP Modules Installing SFP Modules 18 SFP Module with a Bale-Clasp Latch Removing SFP Modules Connecting Cables Connecting the Console PortTypes of RJ-45 Cables Console Port Connecting the Network Cables Connecting Gigabit Ethernet Interface CablesConnecting T1 and E1 Interface Cables Connecting SFP Cables Connecting Cables to the Bits InterfaceConnecting GPS Cables Connecting to Alarm Port Connecting to the Management Ethernet PortDressing Router Cables Powering on the Router Checklist for Power onPower-On Procedure Interpreting Front-Panel LEDs Formatting Procedures for Flash Memory File and Directory ProceduresFormatting Flash Memory as a DOS File System Copying Files Displaying Contents of the Flash Memory Deleting Files from the Flash Memory Displaying File Content Enter a Directory and Determine the Current Directory What to Do After Installing the Hardware Troubleshooting Problem Solving Troubleshooting the Power and Cooling Systems Environmental Reporting FeaturesSymptom Possible Cause Corrective Action Troubleshooting Cables and Connections Information Packet publication Reading the LEDs Chassis LEDsColor/State Location Description T1/E1 Interface LEDs SFP Ethernet Interface LEDs10G SFP+ Ethernet Interface LEDs Color/State Description two LEDs for each T1/E1 port RJ-45 Ethernet Interface LEDs Cable Specifications Gigabit Ethernet Connector Pinouts SFP and SFP+ Port Pinouts and Cable Specifications Pin FE Signal GE SignalT1/E1 Port Pinouts Console Port Signals and Pinouts Pin Signal Name Direction Description Console Port Signals and Pinouts Pin Signal Name HP Pins Direction DescriptionRJ-45-to-DB-9 Terminal Adapter Console Terminal Adapter Device Signal RJ-45 Pin DB-25 Pin Identifying a Rollover CableConsole RJ-45-to-DB-25 Port DTE Bits Port Pinouts Time of Day Pinouts GPS Port Pinouts 10 Mhz Alarm Port Pinouts Pin Signal Name Description Management Ethernet Port Pinouts Auxiliary Port OL-28105-02 Site Log Date Initials Numerics IN-2 IN-3 IN-4