Lantronix LPS1-2, MPS100, LPS1-T manual Altitude, Relative Humidity, Max temp. change/hr 20 C 36 F

Page 58

Environmental Limitations

Specifications

Storage range:-40° to 66° C (-40° to 151° F)

Max temp. change/hr: 20° C (36° F)

Rapid temperature changes may affect operation. Therefore, do not operate the MPS near heating or cooling devices, large windows, or doors that open to the outdoors.

E.2.2 Altitude

Operating maximum: 2.4 km (8,000 ft)

Storage maximum:

9.1 km (30,000 ft)

If operating the MPS above 2.4 km (8000 ft.), decrease the operating temperature rating by 1° F for each 1000 ft.

E.2.3 Relative Humidity

Operating range: 10% to 90% noncondensing, 40% to 60% recommended

Storage range:10% to 90% noncondensing

E-2

Image 58
Contents MPS/LPS Installation Guide For the MPS100, LPS1-T and LPS1-2 Micro Print ServersPage Part Number Rev. B Page Contents LAT Configuration Specifications Page How to Use This Manual IntroductionAppendix F, Frequently-used Commands Installation MPS/LPS Product DescriptionInstalling the MPS Installation Installing the MPS Page Getting Started Configuration MethodsIncoming Logins EZWebConMPSxxxxxxPCL LPSxxxxxxPCL ServicesMPSxxxxxxTEXT LPSxxxxxxTEXT MPSxxxxxxPS LPSxxxxxxPSUsing EZWebCon TCP/IP ConfigurationSetting the IP Address Using a Directed Ping Packet# arp -s 192.0.1.228 00-80-a3-xx-xx-xx % ping Using the Command Line Interface Using a BOOTP, DHCP, or Rarp ReplyLPR Printing LPR on Windows NT 3.5.1 and later TCP/IP Configuration LPR Printing LPR Printing TCP/IP Configuration LPR on Windows 95/98 LPR on Unix HostsLPR on AIX Hosts 8Creating Spooling DirectoryLPR on HP Hosts Printers and Plotters window, choose Printers/Plotters11Configuring Remote Printer LPR on SCO Unix HostsRtel Functionality Unix Host Troubleshooting Area to Check ExplanationNdps Printing NDS Print Queues NetWare ConfigurationObtain an NDS License NetWare Administrator Quick Setup Print Queues Configure your MPSFrom the Menu Bar, select Tools Print Services Quick Setup Pconsole Print QueuesNetWare Host Troubleshooting Use the Show Protocols NetWare Access command. ByCode Meaning Remedy Page LAT Configuration Printing Directly to a PortLAT Host Troubleshooting 4Translating LAT Error CodesBitronics AppleTalk ConfigurationMacintosh Services AppleTalk ZonesAppleTalk Host Troubleshooting MPS Configuration DLC Configuration for LAN ManagerDLC Configuration Host ConfigurationSelect Job-based Contact Information Problem Report ProcedureFull Contact Information Page Troubleshooting Power-up TroubleshootingProblem/Message Error Remedy MPSDhcp Troubleshooting Init Noboot command wasBootp Troubleshooting Rarp TroubleshootingPrinting Problems PostScript ProblemsEntering Commands at the Boot Prompt Bitmap GraphicsFlush NVR Set Bootp Enabled, DisabledSet Dhcp Enabled, Disabled FlashSet IPAddress ipaddress Set Rarp Enabled, DisabledSet Hardware Set Loadhost ipaddressParallel Connectors Ethernet ConnectorPinouts Page Via the Web Updating SoftwareObtaining Software Via FTPReloading Software Reloading SequenceNetWare Tftp Troubleshooting Flash ROM UpdatesMOP Temperature Power Supply CordEnvironmental Limitations Relative Humidity AltitudeMax temp. change/hr 20 C 36 F Frequently-used Commands ConventionsServer Commands Define Server Netware Loadhost Define Server Privileged PasswordDefine Service Appletalk EN/DIS Define Server Rarp EN/DISCancel Define Service DLC EN/DISDefine Service NobootPort Commands Define Port 1 Dtrwait EN/DIS Define Port 1 Bitronics EN/DISDefine Port 1 Dsrlogout EN/DIS Define Port 1 Flow CTSDefine Proto IP EN/DIS Protocol CommandsDefine Proto EN/DIS MpsmpsNetware Ware AccessDefine Proto Native Encapsulation EtheriiWarranty Statement Page Declaration of Conformity Page Symbols IndexMOP Pconsole FTP D-1
Related manuals
Manual 100 pages 51.23 Kb