Lantronix MPS100, LPS1-2, LPS1-T manual Environmental Limitations, Power Supply Cord, Temperature

Page 57

E:

Specifications

E.1

Power Information

E.1.1

Power Requirements

Voltage:

MPS100:

 

 

95-250 V AC, 3-wire single phase, autoranging

 

 

LPS1-T and LPS 1-2:

 

 

110 V AC US, 220 V AC International

Frequency:

47-63 Hz

Operating Current:

MPS100:

 

 

800 mA (maximum) @ 5V Reg. DC

 

 

LPS1-T and LPS1-2:

 

 

700 mA (maximum) @ 6V

Power Consumption:

MPS100:

 

 

25 Watts

 

 

LPS1-T and LPS1-2:

 

 

4.2 Watts

Fuse Rating

1.6A, 250 Volts

E.1.2 Power Supply Cord

Cord type:

3 conductors, 1.0 mm2 minimum conductor size (ap-

 

proximately 18 AWG)

Rated for:

250 Volts AC, 10 Amps

Length:

3.0 meters

E.2 Environmental Limitations

E.2.1 Temperature

Operating range:

5° to 50° C (41° to 122° F)

E-1

Page 56 Page 58
Image 57
Page 56 Page 58
Contents For the MPS100, LPS1-T and LPS1-2 Micro Print Servers MPS/LPS Installation GuidePage Part Number Rev. B Page Contents LAT Configuration Specifications Page Introduction How to Use This ManualAppendix F, Frequently-used Commands MPS/LPS Product Description InstallationInstalling the MPS Installation Installing the MPS Page Incoming Logins Configuration MethodsGetting Started EZWebConMPSxxxxxxTEXT LPSxxxxxxTEXT ServicesMPSxxxxxxPCL LPSxxxxxxPCL MPSxxxxxxPS LPSxxxxxxPSSetting the IP Address TCP/IP ConfigurationUsing EZWebCon Using a Directed Ping Packet# arp -s 192.0.1.228 00-80-a3-xx-xx-xx % ping Using a BOOTP, DHCP, or Rarp Reply Using the Command Line InterfaceLPR Printing LPR on Windows NT 3.5.1 and later TCP/IP Configuration LPR Printing LPR Printing TCP/IP Configuration LPR on Unix Hosts LPR on Windows 95/988Creating Spooling Directory LPR on AIX HostsPrinters and Plotters window, choose Printers/Plotters LPR on HP HostsLPR on SCO Unix Hosts 11Configuring Remote PrinterRtel Functionality Area to Check Explanation Unix Host TroubleshootingNetWare Configuration Ndps Printing NDS Print QueuesObtain an NDS License Configure your MPS NetWare Administrator Quick Setup Print QueuesPconsole Print Queues From the Menu Bar, select Tools Print Services Quick SetupUse the Show Protocols NetWare Access command. By NetWare Host TroubleshootingCode Meaning Remedy Page Printing Directly to a Port LAT Configuration4Translating LAT Error Codes LAT Host TroubleshootingMacintosh Services AppleTalk ConfigurationBitronics AppleTalk ZonesAppleTalk Host Troubleshooting DLC Configuration DLC Configuration for LAN ManagerMPS Configuration Host ConfigurationSelect Job-based Problem Report Procedure Contact InformationFull Contact Information Page Power-up Troubleshooting TroubleshootingMPS Problem/Message Error RemedyInit Noboot command was Dhcp TroubleshootingRarp Troubleshooting Bootp TroubleshootingPostScript Problems Printing ProblemsBitmap Graphics Entering Commands at the Boot PromptSet Dhcp Enabled, Disabled Set Bootp Enabled, DisabledFlush NVR FlashSet Hardware Set Rarp Enabled, DisabledSet IPAddress ipaddress Set Loadhost ipaddressEthernet Connector Parallel ConnectorsPinouts Page Obtaining Software Updating SoftwareVia the Web Via FTPReloading Sequence Reloading SoftwareNetWare Troubleshooting Flash ROM Updates TftpMOP Power Supply Cord TemperatureEnvironmental Limitations Altitude Relative HumidityMax temp. change/hr 20 C 36 F Conventions Frequently-used CommandsServer Commands Define Service Appletalk EN/DIS Define Server Privileged PasswordDefine Server Netware Loadhost Define Server Rarp EN/DISDefine Service Define Service DLC EN/DISCancel NobootPort Commands Define Port 1 Dsrlogout EN/DIS Define Port 1 Bitronics EN/DISDefine Port 1 Dtrwait EN/DIS Define Port 1 Flow CTSDefine Proto EN/DIS Protocol CommandsDefine Proto IP EN/DIS MpsmpsDefine Proto Native Ware AccessNetware Encapsulation EtheriiWarranty Statement Page Declaration of Conformity Page Index SymbolsMOP Pconsole FTP D-1
Related manuals
Manual 100 pages 51.23 Kb
Top Page Image Contents