GarrettCom 6KQE manual C3.0 DUAL-SOURCE OPTION, Theory of Operation

Page 49

Magnum 6KQE Managed Edge Switch Installation and User Guide

02/09

C3.0 DUAL-SOURCE OPTION, THEORY OF OPERATION

 

The Dual-Source DC power option is designed using diodes inside of the chassis on each DC power input line. A diode is placed in each of the four input lines (behind the four external power

connection terminals) so that power from an external source can only flow into the unit. This allows the unit to operate

whenever DC power is correctly

applied to either or both of the two inputs.

C4.0 FEATURES AND BENEFITS OF THE DUAL-SOURCE DESIGN

a)The Switch unit can receive power from either input, “A” or “B”. The hub will normally draw its power from the DC source with the highest voltage at a given time.

b)The Switch unit will not allow power to flow from a higher voltage input to a lower voltage input, i.e. the two DC power sources are not mixed together by the hub.

c)When one correct DC input is present, the Switch will receive power if the other DC input is absent, or even if it is connected with reverse polarity or shorted or grounded.

d)Reverse polarity connections, if they should accidentally occur on either input, will not damage the Switch or power supply internally (nor will it blow the fuse in the internal power supply) because of the blocking action of the diodes. This is true even if one input connection is reversed while the Switch is operating from the other source.

e)The Switch will not receive power (and will not work) when both inputs are simultaneously absent or are both incorrectly connected.

Figure C5.0: DC Dual-Source, wiring connections with Dual-Source option.

Dual Source Terminal block

C5.0 INSTALLATION

This section describes the proper connection of the -48VDC, 12VDC, 24VDC, 125VDC and 250VDC dual source leads to the power terminal block on the Magnum 6KQE Switch (shown in Figure above)

www . GarrettCom . com

44

Image 49
Contents Managed Edge Switch Contacting GarrettCom, Inc GarrettCom, IncCanadian Emissions Statement Electrical Safety requirementsIntroduction Table of ContentsAppendix B DC Power Input TroubleshootingPerformance Technical SpecificationsNetwork Standards and Compliance, hardware Maximum 10 Mbps Ethernet Segment LengthsFiber Single-mode connector types Fiber Multi-mode connector types supportedAlarm Relay Contacts Management Console connectorPower Consumption AC Power Supply InternalDual DC Power Input Optional 6KQE MountingOrdering Information Configuration OptionsWww . GarrettCom . com Inspecting the Package and Product Product Description Magnum 6KQE Managed Edge Switch Packet Prioritization, 802.1p QOS Frame Buffering and Flow Control Web-browser, at ftp//ftp.garrettcom.com Managed Network Software for Magnum 6KQE„ Managed switching for high performance Ethernet LANs Features and Benefits„ Fiber Ports Built-In „ MNS-6K-SECURE optional, for extra securityApplications 5a The industrial factory floor application with Magnum 6KQE Example 1 Magnum 6KQE Switch for an Industrial ApplicationMagnum 6KQE Managed Edge Switch Installation and User Guide Www . GarrettCom . com Locating Magnum 6KQE Switches Connecting Twisted Pair CAT3, CAT5, UTP or STP Connecting Ethernet MediaMedia Ieee Standard Connector Connecting Single-Mode Fiber Optic Connecting Twisted Pair CAT5e or better, UTP or STPGigabit SFP Small Form-factor Pluggable Transceivers Connecting Fiber Optic Cable to SFP TransceiversSee .2 for the SFP’s available for the 6KQE Mounting Dimensions for 6KQE with metal brackets DIN-Rail Mounting the Magnum 6KQE Powering the Magnum 6KQE Managed Edge Switch 5a Alarm Contacts Pin Signal Description Connecting the Console Terminal to Magnum 6KQEDB-9 Console port connector 1 RS-232 DB-9 Console port Serial port pin assignmentsFiltering and Forwarding Switching FunctionalityAddress Learning Auto-CrossMDIX and Auto-negotiation, for RJ-45 ports Flow-control, Ieee 802.3x standard Magnum 6KQE Managed Edge Switch Port Modules Power Budget Calculations for 6KQE Modules with Fiber Media6KQE Modules 1 6KQE Module LED designations 3 6KQE4-RJ45, 4 x 10/100Mb RJ45 Slot C 2 6KQE Base Unit LED designations6KQE4-1MMRJ, 1 x Mtrj / 3 x RJ45 Slot C 6 6KQE4-3MMRJ, 3 x Mtrj / 1 x RJ45 Slot A, Slot C 5 6KQE4-2MMRJ, 2 x Mtrj / 2 x RJ45 Slot C6KQE4-1MLC, 1 x LC / 3 x RJ45 Slot C 9 6KQE4-3MLC, 3 x LC / 1 x RJ45 Slot A, Slot C 8 6KQE4-2MLC, 2 x LC / 2 x RJ45 Slot C10 6KQE4-xSLC, LC Singlemode 20km / RJ45 Module 11 6KQF-xSLCL, LC Singlemode 40km / RJ45 Module13 6KQE-2GSFP, 1GSFP Gigabit SFP Fiber ports Slot D 12 6KQE-2GCU, 1GCU Gigabit RJ45 Copper ports Slot DPoE LEDs Summary 6KQEP-48VDC, Base Unit w/PoE Power-pass-throughBefore Calling for Assistance When Calling for AssistanceNo Problem Found Return Material Authorization RMA ProcedureShipping and Packaging Information Standard 6KQE DC Power Input Terminal Block -, GND, + Fig B1.0 Location of chassis ground Power ConsumptionB2.0 12, 24, -48, 125 and 250VDC POWER, Theory of Operation B4.0 6KQE, 12, 24, -48, 125 and 250VDC Installation B3.0 Applications for DC Powered Ethernet SwitchesB5.0 Operation B4.1 UL Requirements for DC-powered unitsC2.0 Magnum 6KQE, with DC Dual-Source option Appendix C Internal DC Dual-Source Power Input OptionC3.0 DUAL-SOURCE OPTION, Theory of Operation Example Magnum 6KQE-48VDC Dual-Src-48V C6.0 Ordering Information for Dual Source Power