GarrettCom 6KQE manual Connecting Twisted Pair CAT5e or better, UTP or STP

Page 23

Magnum 6KQE Managed Edge Switch Installation and User Guide

02/09

NOTE: for Power Substations: In support of the IEEE 1613 Class 2 standard, GCI advises that, for substation applications, the RJ-45 ports are intended for connectivity to other communication equipment such as routers or telecommunication multiplexers installed in close proximity (i.e., less than 2 meters or 6.5ft) to the 6KQE. It is not recommended to use these ports in substation applications to interface to field devices across distances which could produce high (greater than 2500V ) levels of ground potential rise (GPR) during line-to-ground fault conditions. The 6KQE passes the 1613specifications for zero packet loss with fiber ports & with RJ-45 ports used as indicated here.

3.2.2Connecting Twisted Pair (CAT5e or better, UTP or STP)

The RJ-45 Gigabit ports of the Magnum 6KQE can be connected to the media types, 1000BASE-T or CAT 5E or better 100-ohm UTP or shielded twisted pair (STP) balanced cable. The CAT 5E or better 100-ohm UTP or shielded twisted pair (STP) balanced cable is recommended to use when making 1000BASE-TX connections. In either case, the max distance for unshielded twisted pair cabling is 100 meters (328 ft).

The following procedure describes how to connect a 1000BASE-T twisted pair segment to the RJ-45 port. The procedure is the same for both unshielded and shielded twisted pair cables.

1.1000BASE-T connections require that all four pairs or wires be connected. Insert either end of the cable with an RJ-45 plug into the RJ-45 connector of the port. Note that, even though the connector is shielded, either unshielded or shielded cables and wiring may be used.

2.Connect the other end of the cable to the corresponding device

3.Use the LINK LED to ensure proper connectivity by noting that the LED will be illuminated when the unit is powered and proper connection is established

3.2.3Connecting Single-Mode Fiber Optic

When using single-mode fiber cable, be sure to use single-mode fiber port connectors. Single-mode fiber cable has a smaller diameter than multi-mode fiber cable (9/125 microns for single-mode, 50/125 or 62.5/125 microns for multi-mode where xx/xx are the diameters of the core and the core plus the cladding respectively). Single-mode fiber allows full bandwidth at longer distances, about 70km with the single-mode LC.

www . GarrettCom . com

18

Image 23
Contents Managed Edge Switch Contacting GarrettCom, Inc GarrettCom, IncCanadian Emissions Statement Electrical Safety requirementsIntroduction Table of ContentsAppendix B DC Power Input TroubleshootingMaximum 10 Mbps Ethernet Segment Lengths Technical SpecificationsPerformance Network Standards and Compliance, hardwareManagement Console connector Fiber Multi-mode connector types supportedFiber Single-mode connector types Alarm Relay Contacts6KQE Mounting AC Power Supply InternalPower Consumption Dual DC Power Input OptionalOrdering Information Configuration OptionsWww . GarrettCom . com Inspecting the Package and Product Product Description Magnum 6KQE Managed Edge Switch Packet Prioritization, 802.1p QOS Frame Buffering and Flow Control Web-browser, at ftp//ftp.garrettcom.com Managed Network Software for Magnum 6KQE„ MNS-6K-SECURE optional, for extra security Features and Benefits„ Managed switching for high performance Ethernet LANs „ Fiber Ports Built-InApplications 5a The industrial factory floor application with Magnum 6KQE Example 1 Magnum 6KQE Switch for an Industrial ApplicationMagnum 6KQE Managed Edge Switch Installation and User Guide Www . GarrettCom . com Locating Magnum 6KQE Switches Media Ieee Standard Connector Connecting Ethernet MediaConnecting Twisted Pair CAT3, CAT5, UTP or STP Connecting Single-Mode Fiber Optic Connecting Twisted Pair CAT5e or better, UTP or STPSee .2 for the SFP’s available for the 6KQE Connecting Fiber Optic Cable to SFP TransceiversGigabit SFP Small Form-factor Pluggable Transceivers Mounting Dimensions for 6KQE with metal brackets DIN-Rail Mounting the Magnum 6KQE Powering the Magnum 6KQE Managed Edge Switch 5a Alarm Contacts 1 RS-232 DB-9 Console port Serial port pin assignments Connecting the Console Terminal to Magnum 6KQEPin Signal Description DB-9 Console port connectorAddress Learning Switching FunctionalityFiltering and Forwarding Auto-CrossMDIX and Auto-negotiation, for RJ-45 ports Flow-control, Ieee 802.3x standard 6KQE Modules Power Budget Calculations for 6KQE Modules with Fiber MediaMagnum 6KQE Managed Edge Switch Port Modules 1 6KQE Module LED designations 3 6KQE4-RJ45, 4 x 10/100Mb RJ45 Slot C 2 6KQE Base Unit LED designations6KQE4-1MMRJ, 1 x Mtrj / 3 x RJ45 Slot C 6 6KQE4-3MMRJ, 3 x Mtrj / 1 x RJ45 Slot A, Slot C 5 6KQE4-2MMRJ, 2 x Mtrj / 2 x RJ45 Slot C6KQE4-1MLC, 1 x LC / 3 x RJ45 Slot C 11 6KQF-xSLCL, LC Singlemode 40km / RJ45 Module 8 6KQE4-2MLC, 2 x LC / 2 x RJ45 Slot C9 6KQE4-3MLC, 3 x LC / 1 x RJ45 Slot A, Slot C 10 6KQE4-xSLC, LC Singlemode 20km / RJ45 Module13 6KQE-2GSFP, 1GSFP Gigabit SFP Fiber ports Slot D 12 6KQE-2GCU, 1GCU Gigabit RJ45 Copper ports Slot DPoE LEDs Summary 6KQEP-48VDC, Base Unit w/PoE Power-pass-throughBefore Calling for Assistance When Calling for AssistanceNo Problem Found Return Material Authorization RMA ProcedureShipping and Packaging Information B2.0 12, 24, -48, 125 and 250VDC POWER, Theory of Operation Fig B1.0 Location of chassis ground Power ConsumptionStandard 6KQE DC Power Input Terminal Block -, GND, + B4.0 6KQE, 12, 24, -48, 125 and 250VDC Installation B3.0 Applications for DC Powered Ethernet SwitchesB5.0 Operation B4.1 UL Requirements for DC-powered unitsC2.0 Magnum 6KQE, with DC Dual-Source option Appendix C Internal DC Dual-Source Power Input OptionC3.0 DUAL-SOURCE OPTION, Theory of Operation Example Magnum 6KQE-48VDC Dual-Src-48V C6.0 Ordering Information for Dual Source Power