GarrettCom manual Locating Magnum 6KQE Switches

Page 21

Magnum 6KQE Managed Edge Switch Installation and User Guide

02/09

3.0INSTALLATION

Before installing the equipment, it is necessary to take the following precautions:

1.) If the equipment is mounted in an enclosed or multiple rack assembly, the steady-state long-term environmental temperature around the equipment must be less than or equal to 600C.

2.) If the equipment is mounted in an enclosed or multiple rack assembly, adequate airflow must be maintained for proper and safe operation.

3.) If the equipment is mounted in an enclosed or multiple rack system, placement of the equipment must not overload or load unevenly the rack system.

4.) If the equipment is mounted in an enclosed or multiple rack assembly, verify the equipment’s power requirements to prevent overloading of the building/s electrical circuits.

5.) If the equipment is mounted in an enclosed or multiple rack assembly verify that the equipment has a reliable and uncompromised earthing path.

This section describes installation of the Magnum 6KQE Switches, as well as connection of the various Ethernet media types.

3.1Locating Magnum 6KQE Switches

For vertical panel mounting and wall mounting, see Section 3.3 For vertical DIN-Rail mounting, see Section 3.3.1

For DC power input data, see Appendix B. For Dual Source, see Appendix C

.

The rugged metal case of the Magnum 6KQE will normally protect it from accidental damage in a lab or workplace setting. Maintain an open view of the front to visually monitor the status LEDs. Keep an open area around the unit so that cooling can occur from convection while the unit is in operation. The 6KQE has no fans, so it is silent when in operation. Internal electronics use the case as a heat sink, so the unit may normally be quite warm to the touch.

www . GarrettCom . com

16

Image 21
Contents Managed Edge Switch Contacting GarrettCom, Inc GarrettCom, IncCanadian Emissions Statement Electrical Safety requirementsIntroduction Table of ContentsAppendix B DC Power Input TroubleshootingPerformance Technical SpecificationsNetwork Standards and Compliance, hardware Maximum 10 Mbps Ethernet Segment LengthsFiber Single-mode connector types Fiber Multi-mode connector types supportedAlarm Relay Contacts Management Console connectorPower Consumption AC Power Supply InternalDual DC Power Input Optional 6KQE MountingOrdering Information Configuration OptionsWww . GarrettCom . com Inspecting the Package and Product Product Description Magnum 6KQE Managed Edge Switch Packet Prioritization, 802.1p QOS Frame Buffering and Flow Control Web-browser, at ftp//ftp.garrettcom.com Managed Network Software for Magnum 6KQE„ Managed switching for high performance Ethernet LANs Features and Benefits„ Fiber Ports Built-In „ MNS-6K-SECURE optional, for extra securityApplications 5a The industrial factory floor application with Magnum 6KQE Example 1 Magnum 6KQE Switch for an Industrial ApplicationMagnum 6KQE Managed Edge Switch Installation and User Guide Www . GarrettCom . com Locating Magnum 6KQE Switches Connecting Ethernet Media Connecting Twisted Pair CAT3, CAT5, UTP or STPMedia Ieee Standard Connector Connecting Single-Mode Fiber Optic Connecting Twisted Pair CAT5e or better, UTP or STPConnecting Fiber Optic Cable to SFP Transceivers Gigabit SFP Small Form-factor Pluggable TransceiversSee .2 for the SFP’s available for the 6KQE Mounting Dimensions for 6KQE with metal brackets DIN-Rail Mounting the Magnum 6KQE Powering the Magnum 6KQE Managed Edge Switch 5a Alarm Contacts Pin Signal Description Connecting the Console Terminal to Magnum 6KQEDB-9 Console port connector 1 RS-232 DB-9 Console port Serial port pin assignmentsSwitching Functionality Filtering and ForwardingAddress Learning Auto-CrossMDIX and Auto-negotiation, for RJ-45 ports Flow-control, Ieee 802.3x standard Power Budget Calculations for 6KQE Modules with Fiber Media Magnum 6KQE Managed Edge Switch Port Modules6KQE Modules 1 6KQE Module LED designations 3 6KQE4-RJ45, 4 x 10/100Mb RJ45 Slot C 2 6KQE Base Unit LED designations6KQE4-1MMRJ, 1 x Mtrj / 3 x RJ45 Slot C 6 6KQE4-3MMRJ, 3 x Mtrj / 1 x RJ45 Slot A, Slot C 5 6KQE4-2MMRJ, 2 x Mtrj / 2 x RJ45 Slot C6KQE4-1MLC, 1 x LC / 3 x RJ45 Slot C 9 6KQE4-3MLC, 3 x LC / 1 x RJ45 Slot A, Slot C 8 6KQE4-2MLC, 2 x LC / 2 x RJ45 Slot C10 6KQE4-xSLC, LC Singlemode 20km / RJ45 Module 11 6KQF-xSLCL, LC Singlemode 40km / RJ45 Module13 6KQE-2GSFP, 1GSFP Gigabit SFP Fiber ports Slot D 12 6KQE-2GCU, 1GCU Gigabit RJ45 Copper ports Slot DPoE LEDs Summary 6KQEP-48VDC, Base Unit w/PoE Power-pass-throughBefore Calling for Assistance When Calling for AssistanceNo Problem Found Return Material Authorization RMA ProcedureShipping and Packaging Information Fig B1.0 Location of chassis ground Power Consumption Standard 6KQE DC Power Input Terminal Block -, GND, +B2.0 12, 24, -48, 125 and 250VDC POWER, Theory of Operation B4.0 6KQE, 12, 24, -48, 125 and 250VDC Installation B3.0 Applications for DC Powered Ethernet SwitchesB5.0 Operation B4.1 UL Requirements for DC-powered unitsC2.0 Magnum 6KQE, with DC Dual-Source option Appendix C Internal DC Dual-Source Power Input OptionC3.0 DUAL-SOURCE OPTION, Theory of Operation Example Magnum 6KQE-48VDC Dual-Src-48V C6.0 Ordering Information for Dual Source Power