GarrettCom 6KQE manual C6.0 Ordering Information for Dual Source Power

Page 50

Magnum 6KQE Managed Edge Switch Installation and User Guide

02/09

The terminal block is located on the left front of the unit next to the Alarm terminal block and is equipped with four (4) screw-down lead posts. The primary terminals are identified as positive (A+),

negative (A-), and the secondary power terminals as negative (B-), positive (B+). The chassis is earth/ground (GND). The Dual Source terminal block for the 12, 24, 48, 125 and 250VDC are the same.

Note: The GND should be hooked up first. The 6KQE unit has a floating ground, so the user may elect to Ground either + or - terminal to suit the customer’s use. Before connecting live power lines to the terminal block, always use a digital voltmeter to measure the output voltage of the power supply and determine the lead which is more “+ve potential”. The more “+ve” voltage lead from a +ve or –ve power supply must be connected to the post labeled “+”.

The connection procedure is straightforward. Simply connect the DC leads to the Switch’s power terminals, positive (+) and negative (-) screws. The use of Ground (GND) is optional; it connects to the Switch chassis. Ensure that each lead is securely tightened.

C6.0 ORDERING INFORMATION FOR DUAL SOURCE POWER

To order the optional Dual-Source power supply factory installed, add “Dual- Src-xxxV” as a separate line item following the product model.

Example: Magnum 6KQE-48VDC

Dual-Src-48V

See the Configuration Guide on the GCI web site at http://www.garrettcom.com/techsupport/insertion_guides/6kqecg.pdf for additional information.

www . GarrettCom . com

45

Image 50
Contents Managed Edge Switch GarrettCom, Inc Contacting GarrettCom, IncElectrical Safety requirements Canadian Emissions StatementTable of Contents IntroductionTroubleshooting Appendix B DC Power InputNetwork Standards and Compliance, hardware Technical SpecificationsPerformance Maximum 10 Mbps Ethernet Segment LengthsAlarm Relay Contacts Fiber Multi-mode connector types supportedFiber Single-mode connector types Management Console connectorDual DC Power Input Optional AC Power Supply InternalPower Consumption 6KQE MountingConfiguration Options Ordering InformationWww . GarrettCom . com Inspecting the Package and Product Product Description Magnum 6KQE Managed Edge Switch Packet Prioritization, 802.1p QOS Frame Buffering and Flow Control Managed Network Software for Magnum 6KQE Web-browser, at ftp//ftp.garrettcom.com„ Fiber Ports Built-In Features and Benefits„ Managed switching for high performance Ethernet LANs „ MNS-6K-SECURE optional, for extra securityApplications Example 1 Magnum 6KQE Switch for an Industrial Application 5a The industrial factory floor application with Magnum 6KQEMagnum 6KQE Managed Edge Switch Installation and User Guide Www . GarrettCom . com Locating Magnum 6KQE Switches Media Ieee Standard Connector Connecting Ethernet MediaConnecting Twisted Pair CAT3, CAT5, UTP or STP Connecting Twisted Pair CAT5e or better, UTP or STP Connecting Single-Mode Fiber OpticSee .2 for the SFP’s available for the 6KQE Connecting Fiber Optic Cable to SFP TransceiversGigabit SFP Small Form-factor Pluggable Transceivers Mounting Dimensions for 6KQE with metal brackets DIN-Rail Mounting the Magnum 6KQE Powering the Magnum 6KQE Managed Edge Switch 5a Alarm Contacts DB-9 Console port connector Connecting the Console Terminal to Magnum 6KQEPin Signal Description 1 RS-232 DB-9 Console port Serial port pin assignmentsAddress Learning Switching FunctionalityFiltering and Forwarding Auto-CrossMDIX and Auto-negotiation, for RJ-45 ports Flow-control, Ieee 802.3x standard 6KQE Modules Power Budget Calculations for 6KQE Modules with Fiber MediaMagnum 6KQE Managed Edge Switch Port Modules 1 6KQE Module LED designations 2 6KQE Base Unit LED designations 3 6KQE4-RJ45, 4 x 10/100Mb RJ45 Slot C6KQE4-1MMRJ, 1 x Mtrj / 3 x RJ45 Slot C 5 6KQE4-2MMRJ, 2 x Mtrj / 2 x RJ45 Slot C 6 6KQE4-3MMRJ, 3 x Mtrj / 1 x RJ45 Slot A, Slot C6KQE4-1MLC, 1 x LC / 3 x RJ45 Slot C 10 6KQE4-xSLC, LC Singlemode 20km / RJ45 Module 8 6KQE4-2MLC, 2 x LC / 2 x RJ45 Slot C9 6KQE4-3MLC, 3 x LC / 1 x RJ45 Slot A, Slot C 11 6KQF-xSLCL, LC Singlemode 40km / RJ45 Module12 6KQE-2GCU, 1GCU Gigabit RJ45 Copper ports Slot D 13 6KQE-2GSFP, 1GSFP Gigabit SFP Fiber ports Slot D6KQEP-48VDC, Base Unit w/PoE Power-pass-through PoE LEDs SummaryWhen Calling for Assistance Before Calling for AssistanceReturn Material Authorization RMA Procedure No Problem FoundShipping and Packaging Information B2.0 12, 24, -48, 125 and 250VDC POWER, Theory of Operation Fig B1.0 Location of chassis ground Power ConsumptionStandard 6KQE DC Power Input Terminal Block -, GND, + B3.0 Applications for DC Powered Ethernet Switches B4.0 6KQE, 12, 24, -48, 125 and 250VDC InstallationB4.1 UL Requirements for DC-powered units B5.0 OperationAppendix C Internal DC Dual-Source Power Input Option C2.0 Magnum 6KQE, with DC Dual-Source optionC3.0 DUAL-SOURCE OPTION, Theory of Operation C6.0 Ordering Information for Dual Source Power Example Magnum 6KQE-48VDC Dual-Src-48V