GE GXSV65R, GXSL55R owner manual Installing the Tubing, Install the Battery

Page 13

Installation Instructions

INSTALLING THE TUBING

1.Measure 3/4from the end of each remaining piece of tubing (faucet end and inlet end) and mark with a pencil (Fig. 8). (Check for roundness, smoothness, cuts, nicks, flat spots and sharp edges. It may be necessary to recut the tubing.)

3/4 (19 mm)

Fig. 8

INCORRECT

2.Locate fittings for tubing on bottom of manifold.

INLET

OUTLET

Inlet from

Outlet

supply valve

to faucet

3.NOTE: Water flow is from left to right. Water inlet is on the left side and water outlet is on the right side. Failure to follow will result in water leaks when filter canisters are removed.

4.Push the tubing firmly into each fitting on the manifold until the line is flush with the fitting collar. (If the tubing is removed, re-cut the end, measure, mark and re-insert). Tubing must be fully inserted to avoid leaks (Fig. 9). (To remove tubing, depress and hold white collet; pull tubing out to remove.)

White Collet

(DO NOT REMOVE)

Insertion line

3 4"

 

Insert tubing

 

 

 

Engagement

Fig. 9

 

3/4(3/8tubing)

 

 

INSTALLING THE TUBING (CONT.)

5.Pull out slightly on tubing to ensure a good seal.

6.Install the other end of the tubing from the inlet side of the manifold to the feed water adapter.

NOTE: Inspect the ends of the tubing to be sure there are no imperfections and that the end of the tubing is cut square. It may be necessary to cut the tubing again.

INSTALL THE BATTERY

1.Remove the lens cover from the faucet base. Grip it from both sides and pull forward.

2.Install one CR2032 3V battery with the “+” side down into the battery tray.

3.The amber LED light will flash 5 times, indicating a proper installation and system reset . If the amber light does not flash, check the position of the battery and make sure it is installed correctly.

4.Slide the lens cover back into the faucet base.

5.Normally, the light is off. After 6 months of use, the amber LED light will flash every 30 seconds, indicating the time to replace the filter canister.

NOTE: The amber LED light may stop blinking

if it is allowed to blink for an extended period of time. To ensure proper operation, the battery should be replaced with every filter change.

Faucet Base

Lens Cover

Battery “+” Side Down

 

13

Image 13
Contents Water Filtration System Safety Instructions System OverviewImportant Safety Information Water Filtration System Uses the Following Canisters Specifications GuidelinesModel GXSL55R Model GXSV65R Installation OverviewSmartWater Filtration System GXSL55R Using Filter Fqslf Performance Data SheetParticulate SmartWater Filtration System GXSV65R Using Filter FqsvfContaminant Contents Included With the Product Important Installation RecommendationsCold Water Supply Fitting Optional Home Installation Install the FaucetOptional Installation OD tubing or largerPacket Screw Installation Mounting System InstallationMounting System to Screws Installed in Wall Install the Battery Installing the TubingLocate fittings for tubing on bottom of manifold Slide the lens cover back into the faucet baseReplacement Filter Canisters Estimated Replacement Costs Flush ProcedureProcedure for flushing the GE Water Filtration system is Replacing the Filter CanistersProper installation and operation Before you call for service…Fully follow the filter replacement instructions From systemParts and Accessories Schedule ServiceGE Water Filtration System Warranty Consumer Support GE Appliances WebsiteConseils de dépannage SurlesystèmeMesures DE Sécurité Importantes Modèle GXSL55R DirectivesdecaractéristiquestechniquesVue d’ensemble sur l’installation Moyenne Minimum Feuillet de données relatives à la performanceFQSVF-Cartouche de filtre de remplacement 35-40$ Max. Effluent Installation Préférée Outils ET Matériaux Nécessaires Pour L’INSTALLATIONPièces Comprises Avec LE Produit De filtration d’eauInstallation À Domicile Facultative Installation DU RobinetInstallation Facultative Là où la réglementation le permetPour retirer le robinet Installation DU Robinet SuiteInstallation DE VIS Installation DU Système DE MontageMontage du système aux vis installées dans le mur Installation DU Système DE Montage SuiteEnlevez l’emballage rétrécissable du système de filtre Installation DU Tuyau Suite Installation DU TuyauInstallation DE LA Pile Localisez les raccords des tuyaux en la bas du collecteurProcédure DE Rinçage Remplacement DES Cartouches DE FiltreCirconstances qui peuvent nécessiter un rinçage du système Méthode de rinçage du système de filtration d’eau GEAvant d’appeler un réparateur… Pièces et accessoires Service de réparationsSoutien au consommateur Studio de conception réalisteConsumidor . . . . . . . . . .Cubierta posterior De problemasInformación DE Seguridad Importante Modelo GXSL55R Pautas de las especificacionesGeneralidades sobre la instalación Pautasde las especificacionesModelo GXSV65R Promedio Mínimo Hoja de datos de funcionamientoCalidad del Promedio Effluyente De reducción Contaminante Accesorio Para EL Suministro DE Agua Fría Contenido Incluido CON EL ProductoAdvertencia Lea el manual Instalación PreferidaInstalación Opcional Instalación DEL GrifoOpción Si es necesario perforar, haga un orificio deCorte el suministro de agua Para quitar el grifoInstalación DE LOS Tornillos Montaje DEL SistemaMontaje del sistema a los tornillos instalados en la pared Instalación DE LA Batería Cómo Instalar LA TuberíaVuelva a colocar la tapa del lente en la base del grifo Procedimiento Para Lavar Cómo Reemplazar LOS Cartuchos DE LOS FiltrosRetire el aluminio de la parte superior de Que la tubería no posea rasguños, rebabas, etc. y que esté Antes de solicitar un servicio…Instalada a una profundidad adecuada Solicite una reparación Soporte al consumidor Página Web de GEGarantías ampliadas Piezas y accesorios