EverFocus EFC--02-1-A Show Card Number, Enter Reader Setting Menu, Card ARM Setting

Page 51

reader twice consecutively, his access will be denied and the system will generate an illegal event when the cardholder’s card is configured as APB enabled. Be careful to enable this function in the system with only single side readers installed somewhere.

Card ARM Setting

If a card with arm/disarm function is swiped on the reader, system will temporarily disarm for a short time so that cardholder can enter arm zone without generating an alarm. The disarm time is equal to the door open time.

At the following submenu, press ENT to enter ARM setting:

ARM Setting

The arm status of the current card, i.e., enabled or disabled, will be displayed as shown below. Press ENT to toggle between two statuses. Press CLR to exit.

ARM Enabled [ENT] to Toggle

ARM Disabled [ENT] to Toggle

Show Card Number

This function can be used to show the serial number of a card when it is swiped on

the system reader. Under Card Setting menu, press three times to bring up the following window:

Show Card Number

Press ENT and swipe the card on the system reader. The serial number of the card will be displayed as shown below. Press CLR to exit.

Index #:____

Serial#:________

Reader Setting

Card reader properties can be directly set on the controller, including whether the reader is keypad reader, the allocation of readers to doors, and system reader etc.

Enter Reader Setting Menu

Under System menu, press twice to bring up the following window:

Reader Setting

43

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Flex Series Controller EFC-02-1A Instruction Guide Table of Contents Chapter Page ARM/DISARM Specifications FederalCommunication Commission Interference Statement Product Overview FeaturesParts List Controller Layout Main module Controller LayoutPage Preparing for the Installation Installation ReviewPreparing for the Installation Obtain a Floor PlanDetermining Hardware and Location Entry Card Readers Mounting the Enclosure and Controller Hardware InstallationStep Install a New Module to Controller Installing a Module to ControllerReader/Door Index Conversion Terminal / LED DefinitionsMain Module Terminal Definition Terminal name Function No Terminal name Main Module LED DefinitionLED Meaning Door Module Terminal DefinitionDefinitions of the Door Module Terminals Door Module LED DefinitionTerminal Function Name Alarm Module Terminal DefinitionAlarm Module LED Definition Install and Connecting the ReadersWiegand 26 Format RS232 FormatConnection to an Electric Strike Connection to Door LockConnection to a Magnetic Lock Connection to Door SensorConnection to Fire & Alarm Input Connection to Alarm InputConnection to Request-to-Exit 14 Connecting Alarm-sensor to Controller Connection to Alarm Output16 Normally Closed Connections for Alarm Output Connection to Computer via RS232 Connecting Controller ComputerRS485 Bus Based Networking System Connection to Desktop Reader via RS485RS485 Bus Extension Two Incorrect Connections Connection to Multiple Controllers via RS485Connection to Multiple Controllers via RS485 TCP/IP Based SystemPage Connecting the Power Supply Connecting PowerMount a Backup Battery optional Connection to Backup BatteryReset Controller Before First Use Cover PlacementPage General Operation Guideline Enter System ConfigurationDisplay the Number of Installed Modules Main Setting ItemsDisplay the Firmware Version System Setting Enter System Setting MenuSet Date Format Set Date Auto Daylight Savings TimeSet Time Set System PIN Set Arm PINErase All Events Card Setting Reset All Data and SettingsEnter Card Setting Menu Add Cards Delete CardsDelete a Card by Serial Number Status Setting Set Card PropertiesDelete All Cards Access Right Setting Group SettingSet Card PIN Setting Anti Passback APB Setting Show Card Number Reader SettingEnter Reader Setting Menu Card ARM SettingReader to Door Allocation Keypad SettingOpen Time Setting Door SettingSystem Reader Setting Enter Door Setting MenuSet Door Hold Open Time Set Door Behavior at Fire AlarmAlarm Setting Components for AlarmAlarm Configuration Basics Alarm Setting Menu Structure Enter Alarm Setting MenuEnter Alarm Action Setting Sub-menu Fire Alarm Enter Extended Alarm Setting Sub-menuZone Alarm 1~8 SYS PIN FailARM PIN Fail Expired Card AlarmRemote Alarm Unknown CardCard Anti-Passback Fail Invalid CardInvalid Door Invalid TimeCard PIN Fail Door Forced OpenDoor Held Open Reader Lost Armzone SettingEnter Alarm Time Setting Sub-menu Enter Armzone Setting MenuSet Active Armzone Set ARM Delay TimeArm the System using the Controller Keypad Address SettingClear the Alarm Disarm the System using the Controller KeypadYellow LED Status System ARM Status Arm/Disarm the System using a ReaderPage Install the Software in the Control Computer Software SetupConfigure the Controller and All Other Hardware Setup the User Accounts for the SoftwareEnroll Cards Page Page Page EverAccess

EFC--02-1-A specifications

The EverFocus EFC--02-1-A is an advanced video surveillance solution designed to meet the high demands of modern security systems. This device stands out for its robust features, cutting-edge technologies, and exceptional reliability, making it ideal for a wide range of surveillance applications, from retail environments to industrial facilities.

One of the primary features of the EFC--02-1-A is its superior image quality. Equipped with high-definition video capabilities, the camera can capture crystal-clear images even in low-light conditions, thanks to its advanced low-light technology. This ensures that vital details are recorded, enhancing the overall effectiveness of surveillance efforts. The device boasts a wide dynamic range (WDR), which allows it to handle scenes with both bright and dark areas, maintaining image clarity and detail regardless of lighting variations.

The EFC--02-1-A also supports multi-streaming capabilities, enabling simultaneous transmission of multiple video streams in different resolutions. This versatility is particularly advantageous for network bandwidth management, allowing users to customize their surveillance setup according to specific requirements. The integration of advanced compression technologies such as H.265 ensures efficient use of storage while maintaining high video quality.

Durability is another hallmark of the EFC--02-1-A. The camera is designed to withstand harsh environmental conditions, featuring an IP67-rated enclosure that protects it from dust and water ingress. This weatherproof design makes it suitable for both indoor and outdoor installations, ensuring uninterrupted operation in various settings.

Moreover, the EFC--02-1-A comes equipped with smart analytics capabilities, including motion detection and face recognition technologies. These features enhance the system’s functionality by enabling automatic alerts and efficient monitoring of specific areas, thereby reducing the workload for security personnel.

Lastly, seamless integration is a core characteristic of the EFC--02-1-A. It is compatible with multiple video management systems (VMS) and can easily connect with other security devices, promoting a holistic security ecosystem. This interoperability, coupled with user-friendly operational features and remote access capabilities, positions the EverFocus EFC--02-1-A as a leading choice for organizations aiming to enhance their surveillance setups.
Top Page Image Contents