Enterasys Networks A2H124-24P, A2H124-48P manual

Page 3

Electrical Hazard: Only qualified personnel should perform installation procedures.

Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion.

Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden.

Notice

Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice. The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made.

The hardware, firmware, or software described in this document is subject to change without notice.

IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS DOCUMENT, WEB SITE, OR THE INFORMATION CONTAINED IN THEM, EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED OF, KNEW OF, OR SHOULD HAVE KNOWN OF, THE POSSIBILITY OF SUCH DAMAGES.

Enterasys Networks, Inc.

50 Minuteman Road

Andover, MA 01810

2007 Enterasys Networks, Inc. All rights reserved. Part Number: 9034154‐03 February 2007

ENTERASYS, ENTERASYS NETWORKS, ENTERASYS MATRIX, LANVIEW, NETSIGHT, WEBVIEW, and any logos associated therewith, are trademarks or registered trademarks of Enterasys Networks, Inc., in the United States and other countries.

All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.

Documentation URL: http://www.enterasys.com/support/manuals

Documentacion URL: http://www.enterasys.com/support/manuals

Dokumentation im Internet: http://www.enterasys.com/support/manuals

i

Image 3
Contents SecureStack A2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Page Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures MGBIC-08 Who Should Use This Guide About This GuideRelated Documents How to Use This GuideFollowing conventions are used in this guide Conventions Used in This GuideConventions Used in This Guide Xviii About This Guide Introduction A2H124-24P and A2H124-48P OverviewBack A2H124-24P Stackable SwitchPoE Power over Ethernet Support Redundant Power Supply CapabilityStack Connections Power Device Classifications Usage ConnectivityDescription of Mini-GBICs Standards Compatibility Switch Configuration Using WebViewSwitch Configuration Using CLI Commands ManagementGetting Help Lanview Diagnostic LEDsGetting Help Introduction 10BASE-T Network Network Requirements100BASE-TX Network 1000BASE-FX Network1000BASE-T Network Hardware Installation Required Tools Considerations Prior to InstallationUnpacking the Switch Contents of Switch CartonInstalling the Rubber Feet Installing the Switch on a Flat SurfaceChassis Bottom, Rubber Feet Placement Area Guidelines for Switch Installation on Flat Surface Guidelines for Flat Surface InstallationRack Mounting the Switch Guidelines for Rackmount InstallationAttaching Brackets and Installing in Rack Fastening the Switch to the Rack Connecting Stacking CablesStacking Cable Connections About SecureStack A2 Switch Operation in a Stack Configuring Switches in a StackInstalling a New Stackable System of Up to Eight Switches Recommended Procedures for New and Existing StacksImportant Considerations About Using Clear Config in a Stack AC Power Connecting AC and PoE PowerAccessing the RPS connector C2RPS-PoE Redundant Power SystemStack Initialization Overview Connecting to Console Port for Local ManagementDB9 Male Console Port Pinout Assignments What Is NeededConnecting an IBM PC or Compatible Connecting to an IBM or Compatible Device10 Connecting a VT Series Terminal Connecting to a VT Series Terminal11 Connecting to a Modem Connecting to a ModemConnecting UTP Cables Connecting to the Network12 Connecting a UTP Cable Segment to RJ45 Port 13 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX Installing Optional Mini-GBICs Preparation 17 Mini-GBIC with RJ45 Connector 18 Mini-GBIC with MT-RJ Connector Removing the Mini-GBIC 19 Mini-GBIC with LC ConnectorConnecting Fiber-Optic Cables to MT-RJ Ports Installing Optional Mini-GBICs A2H124-24P Connecting Fiber-Optic Cables to LC Ports 21 Cable Connection to LC Fiber-Optic Connectors Initial Logon to Switch Management Completing the InstallationTroubleshooting Lanview LEDs of A2H124-24P Using LanviewColor State Recommended Action Lanview LEDsDown RPS LED Configuration Guide for proper setup Troubleshooting ChecklistConfiguration Guide for the IP address Reset Password Switch Using the Reset Password SwitchUsing the Reset Password Switch Troubleshooting Table A-1 A2H124-24P Switch Specifications Switch SpecificationsEnvironmental PhysicalTable A-2 A2H124-48P Switch Specifications Table A-3 Mini-GBIC Input/Output Port Specifications Mini-GBIC Input/Output SpecificationsGigabit Ethernet Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-SX Table A-11 MGBIC-08 Operating Range 1550 nm MGBIC-LC09 Specifications 1000BASE-LXMGBIC-08 Specifications 1000BASE-ELX Table A-10 MGBIC-08 Optical Specifications 10 µm SMFMGBIC-02 Specifications 1000BASE-T Table A-12 MGBIC-02 SpecificationsConsole Port Pinout Assignments Table A-13 Compliance Standards Regulatory Compliance Regulatory ComplianceIndex Pinout assignments console port A-7