Enterasys Networks A2H124-48P, A2H124-24P Removing the Mini-GBIC, Mini-GBIC with LC Connector

Page 56

Installing Optional Mini-GBICs

Figure 3-19 Mini-GBIC with LC Connector

25 26 27 28

Ã

Á

Â

25/Up 26/Down

Stack

À

A2H124-24P

1	SFP Slot	3	Release tab
2	Mini-GBIC (MGBIC-LC01,-LC03, -LC09, MGBIC-08)	4	Link/Activity LED

Removing the Mini-GBIC

Caution: Do NOT remove a Mini-GBIC from a slot without releasing the locking tab located under the front bottom end of the Mini-GBIC. This can damage the Mini-GBIC.

The Mini-GBIC and its host switch are sensitive to static discharges. Use an antistatic wrist strap and observe all static precautions during this procedure. Failure to do so could result in damaging the Mini-GBIC or host switch. Always leave the Mini-GBIC in the antistatic bag or an equivalent antistatic container when not installed.

Precaución: NO quite el Mini-GBIC de la ranura sin antes abrir la traba ubicada en la parte frontal del Mini-GBIC.

Si lo hace, puede dañar el Mini-GBIC, puesto que es muy sensible a las descargas de electricidad estática, al igual que el dispositivo host. Utilice la pulsera antiestática y tome todas las precauciones necesarias durante este procedimiento. Si no lo hace, pude dañar el Mini-GBIC o el dispositivo host. Mientras no esté instalado, mantenga el Mini-GBIC en su bolsa antiestática o en cualquier otro recipiente antiestático.

3-26 Hardware Installation

Image 56

Contents SecureStack A2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Page Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures MGBIC-08 About This Guide Who Should Use This GuideHow to Use This Guide Related DocumentsConventions Used in This Guide Following conventions are used in this guideConventions Used in This Guide Xviii About This Guide Introduction Overview A2H124-24P and A2H124-48PA2H124-24P Stackable Switch BackStack Connections PoE Power over Ethernet SupportRedundant Power Supply Capability Description of Mini-GBICs Power Device Classifications UsageConnectivity Switch Configuration Using WebView Switch Configuration Using CLI CommandsManagement Standards CompatibilityLanview Diagnostic LEDs Getting HelpGetting Help Introduction Network Requirements 10BASE-T Network1000BASE-T Network 100BASE-TX Network1000BASE-FX Network Hardware Installation Considerations Prior to Installation Unpacking the SwitchContents of Switch Carton Required ToolsInstalling the Switch on a Flat Surface Installing the Rubber FeetChassis Bottom, Rubber Feet Placement Guidelines for Flat Surface Installation Area Guidelines for Switch Installation on Flat SurfaceAttaching Brackets and Installing in Rack Rack Mounting the SwitchGuidelines for Rackmount Installation Connecting Stacking Cables Fastening the Switch to the RackStacking Cable Connections Configuring Switches in a Stack About SecureStack A2 Switch Operation in a StackRecommended Procedures for New and Existing Stacks Installing a New Stackable System of Up to Eight SwitchesImportant Considerations About Using Clear Config in a Stack Connecting AC and PoE Power AC PowerC2RPS-PoE Redundant Power System Accessing the RPS connectorConnecting to Console Port for Local Management Stack Initialization OverviewWhat Is Needed DB9 Male Console Port Pinout AssignmentsConnecting to an IBM or Compatible Device Connecting an IBM PC or CompatibleConnecting to a VT Series Terminal 10 Connecting a VT Series TerminalConnecting to a Modem 11 Connecting to a ModemConnecting to the Network Connecting UTP Cables12 Connecting a UTP Cable Segment to RJ45 Port 13 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX Installing Optional Mini-GBICs Preparation 17 Mini-GBIC with RJ45 Connector 18 Mini-GBIC with MT-RJ Connector 19 Mini-GBIC with LC Connector Removing the Mini-GBICConnecting Fiber-Optic Cables to MT-RJ Ports Installing Optional Mini-GBICs A2H124-24P Connecting Fiber-Optic Cables to LC Ports 21 Cable Connection to LC Fiber-Optic Connectors Completing the Installation Initial Logon to Switch ManagementTroubleshooting Using Lanview Lanview LEDs of A2H124-24PLanview LEDs Color State Recommended ActionDown RPS LED Troubleshooting Checklist Configuration Guide for proper setupConfiguration Guide for the IP address Using the Reset Password Switch Reset Password SwitchUsing the Reset Password Switch Troubleshooting Switch Specifications Table A-1 A2H124-24P Switch SpecificationsPhysical EnvironmentalTable A-2 A2H124-48P Switch Specifications Mini-GBIC Input/Output Specifications Gigabit Ethernet SpecificationsMGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX Table A-3 Mini-GBIC Input/Output Port SpecificationsMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LX MGBIC-08 Specifications 1000BASE-ELXTable A-10 MGBIC-08 Optical Specifications 10 µm SMF Table A-11 MGBIC-08 Operating Range 1550 nmConsole Port Pinout Assignments MGBIC-02 Specifications 1000BASE-TTable A-12 MGBIC-02 Specifications Regulatory Compliance Table A-13 Compliance Standards Regulatory ComplianceIndex Pinout assignments console port A-7